Storage events organized by severity

The following table lists all Storage events, organized by severity (Information, Error, and Warning).

Table 1. Events organized by severity
Event ID Message String Severity
FQXDE0100I Event log cleared Informational
FQXDE0101I Start of delayed events Informational
FQXDE0102I End of delayed events Informational
FQXDE0103I A needs-attention condition was raised by the controller firmware Informational
FQXDE0104I A needs-attention condition was cleared by the controller firmware Informational
FQXDE0105I Unknown event occurred that is not found in event configuration table. Informational
FQXDE0106I A needs-attention condition was suppressed due to event configuration table settings. Informational
FQXDE0107I An event that would have caused a needs-attention condition was suppressed and now is cleared Informational
FQXDE0108I All non-alertable events are temporarily being discarded Informational
FQXDE0109I All events are now being saved and persisted Informational
FQXDE1004I Error on drive open. Informational
FQXDE100AI Drive returned CHECK CONDITION Informational
FQXDE100DI Timeout on drive side of controller Informational
FQXDE1012I Destination driver error Informational
FQXDE1015I Incorrect mode parameters modified and saved on drive Informational
FQXDE1016I Drive returned unrecoverable media error Informational
FQXDE1017I Fibre channel link down Informational
FQXDE1018I Fibre channel link up Informational
FQXDE1019I Extended Fibre Channel link down (more than one minute) Informational
FQXDE101FI Summary of impending drive failure detected by controller Informational
FQXDE1021I Slow drive detected by drive performance analyzer. Info for Analysis Purposes Informational
FQXDE1022I Drive not compared by drive performance analyzer Informational
FQXDE1023I Drive copy triggered by a controller detected impending drive failure Informational
FQXDE1024I Start or restart of issuing unmaps to a drive Informational
FQXDE1025I Completion of all unmap requests to a drive Informational
FQXDE1026I Abnormal decisions were made for drives undergoing provisioning unmaps, not limited to errors Informational
FQXDE1201I Fibre channel - LIP reset received Informational
FQXDE1202I Fibre channel - TGT reset received Informational
FQXDE1203I Fibre channel - TPRLO reset received Informational
FQXDE1205I Fibre channel - driver detected error during initialization Informational
FQXDE1206I Fibre channel link errors continue Informational
FQXDE120BI SFP changed to Optimal Informational
FQXDE120CI Fibre channel loopback diagnostic failed Informational
FQXDE120EI Host-side SFP optimal Informational
FQXDE1300I InfiniBand channel loopback diagnostic failed Informational
FQXDE1301I InfiniBand port up Informational
FQXDE1302I InfiniBand port down Informational
FQXDE1303I InfiniBand - TGT reset received Informational
FQXDE1400I Password reset to default Informational
FQXDE1401I XCopy Lite was disabled Informational
FQXDE1402I XCopy Lite was enabled Informational
FQXDE1404I This event indicates that the controller is no longer experiencing excessive reboots Informational
FQXDE1500I Channel initialization error Informational
FQXDE1501I Selective LIP reset issued to drive Informational
FQXDE1502I Selective LIP reset issued to alternate controller Informational
FQXDE1503I Selective LIP reset issued to IOM (ESM) Informational
FQXDE1507I Loop port bypass (LPB) issued to drive Informational
FQXDE150AI Unresponsive drive (bad AL_PA error) Informational
FQXDE150BI Unresponsive alternate controller (bad AL_PA error) Informational
FQXDE150CI Unresponsive IOM (ESM) (bad AL_PA error) Informational
FQXDE1511I Channel miswire resolved Informational
FQXDE1512I IOM (ESM) miswire resolved Informational
FQXDE1514I Drive channel changed to optimal Informational
FQXDE1516I Switch on chip (SOC) EEPROM failed Informational
FQXDE1517I Switch on chip (SOC) EEPROM cannot be initialized Informational
FQXDE1518I SFP link speed mismatch detected Informational
FQXDE1519I SFP link speed mismatch resolved Informational
FQXDE151BI Optical link speed detection failure resolved Informational
FQXDE151CI Copper link speed detection failure Informational
FQXDE151DI Copper link speed detection failure resolved Informational
FQXDE151FI Controller miswire for drive channel cleared Informational
FQXDE1520I Internal Drive Port PTBI Failure Informational
FQXDE1523I Drive enclosure type miswire clear Informational
FQXDE1526I Trunk state enabled Informational
FQXDE1527I Trunk state disabled Informational
FQXDE1528I Corrected trunk incompatible IOM (ESM) Informational
FQXDE1529I Trunk miswire corrected Informational
FQXDE1651I SAS host channel miswire resolved Informational
FQXDE1653I SAS source driver detected regular initiator overflow Informational
FQXDE1655I Host wide port link is up Informational
FQXDE1656I Host wide port link is down Informational
FQXDE1657I Host wide port link is optimal Informational
FQXDE1658I A host card SAS port connection speed is below the maximum Informational
FQXDE1659I An SMP Timeout event has occurred to a switch connected on a host channel. Check host channel switches for possible issues. Informational
FQXDE165BI The controller detected that a SAS IOC has faulted Informational
FQXDE165CI The controller detected that a SAS IOC has faulted and started a recovery procedure in an attempt to bring it back to an operational state Informational
FQXDE165DI The controller detected that a SAS IOC has faulted and completed a recovery procedure. The SAS IOC was recovered and is now in an operational state Informational
FQXDE1701I Invalid SAS topology resolved Informational
FQXDE1703I SAS host adapter miswire resolved Informational
FQXDE1705I SAS IOM (ESM) miswire resolved Informational
FQXDE1708I Single connection established through previously failed wide port Informational
FQXDE1709I All connections established through wide port Informational
FQXDE170BI Drive expansion port miswire resolved Informational
FQXDE170CI SAS host port configuration error Informational
FQXDE1711I Controller wide port has gone to degraded state Informational
FQXDE1712I Controller wide port has gone to optimal state Informational
FQXDE1717I Link in the controller tray is slow Informational
FQXDE1718I Expansion tray link is slow Informational
FQXDE1719I SAS drive link is slow Informational
FQXDE171BI Access to expansion trays restored Informational
FQXDE1801I Authentication failure Informational
FQXDE1802I Unsupported authentication type Informational
FQXDE1804I iSNS server failure Informational
FQXDE1805I iSNS server contacted Informational
FQXDE1806I Forced session end Informational
FQXDE1807I IP address failure Informational
FQXDE1808I Login failure Informational
FQXDE180CI Connection terminated unexpectedly Informational
FQXDE180DI Session terminated unexpectedly Informational
FQXDE180EI iSCSI interface correctable ECC error occurred Informational
FQXDE180FI iSCSI interface restarted Informational
FQXDE1810I DHCP failure in iSCSI interface Informational
FQXDE1811I DHCP success Informational
FQXDE1812I iSCSI IPV6 error, configuration change, or duplicate IP address detected Informational
FQXDE1813I iSCSI data overrun Informational
FQXDE1814I ISCSI carrier was detected Informational
FQXDE1815I ISCSI carrier was lost Informational
FQXDE1816I iSCSI connection speed warning Informational
FQXDE1817I iSCSI communication was established Informational
FQXDE1818I iSCSI communication lost to remote target Informational
FQXDE1819I iSCSI duplicate IPv4 address Informational
FQXDE1900I Cache memory DIMM detected Informational
FQXDE1901I Cache memory DIMM is missing Informational
FQXDE1902I Host interface card added Informational
FQXDE1903I Host interface card removed Informational
FQXDE1905I Host interface card replaced with same board type Informational
FQXDE1906I Host interface card replaced with different board type Informational
FQXDE200FI Cache synchronization started Informational
FQXDE2010I Cache synchronization completed Informational
FQXDE2011I Cache flush started Informational
FQXDE2012I Cache flush completed Informational
FQXDE2013I Unwritten data/parity recovered from cache Informational
FQXDE2014I VDD logged an error Informational
FQXDE2015I Uncompleted writes detected in NVSRAM at start-of-day Informational
FQXDE2016I Interrupted writes processed Informational
FQXDE2017I Interrupted writes detected from checkpoint logs Informational
FQXDE201CI VDD recover started Informational
FQXDE201DI VDD recover completed Informational
FQXDE201EI VDD repair started Informational
FQXDE201FI VDD repair completed Informational
FQXDE2020I Piece failed during interrupted write Informational
FQXDE2021I Virtual disk failed during interrupted write Informational
FQXDE2022I Media scan (scrub) started Informational
FQXDE2023I Media scan (scrub) completed Informational
FQXDE2024I Media scan (scrub) resumed Informational
FQXDE2025I Reconstruction started Informational
FQXDE2026I Reconstruction completed Informational
FQXDE2027I Reconstruction resumed Informational
FQXDE2028I Modification (reconfigure) started Informational
FQXDE2029I Modification (reconfigure) completed Informational
FQXDE202AI Modification (reconfigure) resumed Informational
FQXDE202BI Redundancy check started Informational
FQXDE202CI Redundancy check completed Informational
FQXDE202FI Automatic volume transfer completed Informational
FQXDE2030I Initialization completed on volume Informational
FQXDE2031I Initialization started on volume Informational
FQXDE2032I Initialization resumed on volume Informational
FQXDE2033I Parity reconstructed on volume Informational
FQXDE2035I Redundancy not consistent Informational
FQXDE2036I Redundancy consistent after retry Informational
FQXDE2037I Redundancy not verified Informational
FQXDE2038I Media scan cycle started on unused drives Informational
FQXDE2039I Media scan cycle on unassigned drives completed Informational
FQXDE203DI Drive adopted Informational
FQXDE203EI FDE drive re-provisioned Informational
FQXDE203FI FDE drive re-provision failed Informational
FQXDE2040I FDE secure component conversion Informational
FQXDE2043I Threshold exceeded during successful mismatch correction Informational
FQXDE2044I IO shipping implicit volume transfer Informational
FQXDE2049I Fail-back implicit volume transfer Informational
FQXDE204AI Auto Load Balancing implicit volume transfer Informational
FQXDE204BI The reconstruction agent failed to enable drive write caching as part of rebuild Informational
FQXDE204CI The reconstruction agent failed to sync drive write caching as part of rebuild Informational
FQXDE204DI The reconstruction agent failed to disable drive write caching as part of rebuild Informational
FQXDE2060I Data assurance mismatch detected - probable cause is channel interface Informational
FQXDE2061I Data assurance mismatch detected - probable cause is cached data Informational
FQXDE2062I Data assurance mismatch detected - probable cause is data on drive Informational
FQXDE2064I Data assurance error detected during cache backup Informational
FQXDE2066I A protected volume to LUN mapping was automatically deleted Informational
FQXDE2067I Host data assurance change Informational
FQXDE2068I Cluster data assurance change Informational
FQXDE206BI Controller has exited Analysis Lockdown Mode Informational
FQXDE206CI Controller has exited Data Assurance Service Mode Informational
FQXDE206DI Data assurance mismatch detected -- cached data recovered from alternate Informational
FQXDE206EI PI errors on cache data blocks were repaired Informational
FQXDE206FI Data assurance mismatch detected -- data recovered, but volume degraded Informational
FQXDE2070I Data assurance mismatch detected -- cached data error on both controllers Informational
FQXDE2101I Alternate controller checked in late Informational
FQXDE2102I Cache mirroring on controllers not synchronized Informational
FQXDE2105I Controller cache reconfigure event Informational
FQXDE210AI Controller cache not enabled or was internally disabled Informational
FQXDE210BI Cache between controllers not synchronized Informational
FQXDE210FI Controller cache memory parity error detected Informational
FQXDE2112I Controller cache battery is fully charged Informational
FQXDE2117I Controller cache manager error cleared Informational
FQXDE211AI Cache corrected by using alternate controller's cache Informational
FQXDE211CI Battery pack is charging Informational
FQXDE211DI Persistent single-bit memory ECC event - recovered Informational
FQXDE2127I Insufficient cache backup device capacity for non-critical data Informational
FQXDE2129I Cache backup device error Informational
FQXDE212AI Cache database mismatch was detected Informational
FQXDE212CI Write-back caching fully restored Informational
FQXDE212DI A cache data loss occurred but no action is required from the user Informational
FQXDE212FI Cache manager enabled secondary cache Informational
FQXDE2130I Secondary cache not enabled because of initialization timeout Informational
FQXDE2202I Volume added Informational
FQXDE2203I Volume group or volume deleted Informational
FQXDE2204I I/O is resumed Informational
FQXDE2206I Reconstruction completed Informational
FQXDE2207I Device copy completed Informational
FQXDE2208I Modification (reconfigure) setup Informational
FQXDE220AI Copyback started Informational
FQXDE2213I Volume initialized with zeros Informational
FQXDE2215I Drive marked failed Informational
FQXDE2216I Piece taken out of service Informational
FQXDE2217I Piece failed Informational
FQXDE221AI Piece replaced Informational
FQXDE221BI Piece placed in service Informational
FQXDE221CI Component placed offline Informational
FQXDE221FI Immediate availability initialization (IAF) completed on volume Informational
FQXDE2220I Hot spare drive added to hot spare list Informational
FQXDE2221I Hot spare drive removed from hot spare list Informational
FQXDE2222I Logical unit number for volume reassigned Informational
FQXDE2224I Reconstruction started Informational
FQXDE2226I Drive spun down Informational
FQXDE2227I Drive marked optimal Informational
FQXDE2228I Drive deleted Informational
FQXDE222EI Mark drive removed Informational
FQXDE2231I Drive marked removed Informational
FQXDE2233I Unassigned drive marked removed Informational
FQXDE2234I Reconstructing drive marked removed Informational
FQXDE2235I Optimal/Replaced drive marked removed Informational
FQXDE2236I Hot spare drive copy completed Informational
FQXDE2247I Data lost on volume during unrecovered interrupted write Informational
FQXDE224CI Wrong drive removed/replaced Informational
FQXDE224FI Hot spare capacity not sufficient for all drives Informational
FQXDE2256I Copyback completed on volume Informational
FQXDE225AI Immediate availability initialization (IAF) started on volume Informational
FQXDE225CI Controller in stopped state Informational
FQXDE225DI Automatic configuration started Informational
FQXDE225EI Automatic configuration completed successfully Informational
FQXDE225FI Automatic configuration failed Informational
FQXDE2261I Controller clocks set by NTP or SNTP Server Informational
FQXDE2263I The drive replacement succeeded Informational
FQXDE2264I The drive replacement failed Informational
FQXDE2268I Component's capacity was reduced Informational
FQXDE2269I Export volume group drive unusable Informational
FQXDE226AI Dacstore region has moved Informational
FQXDE226FI Solid state drive nearing end of life Informational
FQXDE2279I IAF suspended for reconstruction Informational
FQXDE227AI IAF resumed Informational
FQXDE227BI Reconfiguration suspended Informational
FQXDE227DI Drive copy triggered by solid state drive at end of life Informational
FQXDE227EI Drive copy started Informational
FQXDE227FI Drive copy started Informational
FQXDE2280I Drive copy completed and drive failed Informational
FQXDE2281I Drive copy completed and drive replaced Informational
FQXDE2282I Drive copy canceled Informational
FQXDE2283I Drive copy suspended Informational
FQXDE2284I Drive copy resumed Informational
FQXDE2286I Drive copy triggered by a drive detected impending failure Informational
FQXDE228AI . After controllers are rebooted, the NTP state is compared on the two controllers. In this case, they were found to be different, for example, one controller has NTP enabled and the other has NTP disabled. Although this is unconventional, it might be intentional Informational
FQXDE2306I Mismatched midplane EEPROM contents one controller Informational
FQXDE2307I Chassis serial number was corrected Informational
FQXDE2400I Hot swap monitor detected drive removal Informational
FQXDE2401I Hot swap monitor detected drive insertion Informational
FQXDE2506I A missing controller was reinserted Informational
FQXDE2600I Automatic controller firmware synchronization started Informational
FQXDE2601I Automatic controller firmware synchronization completed Informational
FQXDE2603I Default volume created Informational
FQXDE2605I Start-of-day routine completed Informational
FQXDE2606I Start-of-day routine begun Informational
FQXDE2700I Controller RPA memory parity error detected Informational
FQXDE2702I Controller unexpected RPA interrupt detected Informational
FQXDE2703I Recoverable error in processor memory detected/corrected Informational
FQXDE2802I UPS battery is fully charged Informational
FQXDE2809I Controller tray component changed to optimal Informational
FQXDE280CI Drive tray component changed to optimal Informational
FQXDE2817I Tray ID conflict resolved Informational
FQXDE281AI Temperature changed to optimal Informational
FQXDE281FI IOM (ESM) firmware mismatch resolved Informational
FQXDE2824I Drive by-passed condition resolved Informational
FQXDE282AI Controller redundancy restored Informational
FQXDE282CI Drive tray path redundancy restored Informational
FQXDE282EI Drive path redundancy restored Informational
FQXDE2834I Controller host interface card ID mismatch resolved Informational
FQXDE2837I Discrete lines diagnostic failure resolved Informational
FQXDE2839I Interconnect/battery canister reinserted Informational
FQXDE2840I Controller submodel not set or not supported Informational
FQXDE2842I Controller submodel mismatch resolved Informational
FQXDE2847I GBIC/SFP Installed Informational
FQXDE2848I GBIC/SFP removed Informational
FQXDE284AI IOM (ESM) Hardware mismatch resolved Informational
FQXDE284DI Drive tray expansion limit out of range Informational
FQXDE2850I Drive trays cabled correctly Informational
FQXDE2851I Enclosure EEPROM read failure Informational
FQXDE2853I IOM (ESM) configuration settings version mismatch cleared Informational
FQXDE2858I Drawer closed Informational
FQXDE2859I Host-side SFP installed Informational
FQXDE285AI Host-side SFP removed Informational
FQXDE285BI Drive-side SFP installed Informational
FQXDE285CI Drive-side SFP removed Informational
FQXDE2860I The drawer's status is optimal Informational
FQXDE2865I Host-side SFP optimal Informational
FQXDE2901I Leaving invalid system configuration Informational
FQXDE3000I Format unit issued Informational
FQXDE3002I Reassign blocks issued from host Informational
FQXDE3006I Safe pass-through issued Informational
FQXDE3007I Mode select for page 1 received Informational
FQXDE3009I Mode for caching page 8 received Informational
FQXDE300AI Mode select for control mode page A received Informational
FQXDE300DI Mode select for redundant controller page 2C received Informational
FQXDE3012I Write buffer received Informational
FQXDE3014I Drive firmware download started Informational
FQXDE301AI Drive firmware download failed Informational
FQXDE301BI Drive firmware and/or interposer firmware download is completed Informational
FQXDE301CI IOM (ESM) firmware download started Informational
FQXDE301DI IOM (ESM) firmware download failed Informational
FQXDE301EI IOM (ESM) firmware download completed Informational
FQXDE301FI Unable to register a volume due to insufficient resources Informational
FQXDE3020I Update of power supply firmware was blocked Informational
FQXDE3021I Update of power supply firmware failed Informational
FQXDE3022I Update of power supply firmware started Informational
FQXDE3023I Update of power supply firmware completed Informational
FQXDE3024I All drive downloads complete Informational
FQXDE3025I A Set Target Port Groups (STPG) command was received for this volume and caused the volume to be transferred Informational
FQXDE3101I Asynchronous event notification (AEN) was posted for recently logged event Informational
FQXDE3300I Autocode synchronization drive image write started Informational
FQXDE3301I Autocode synchronization drive image write completed Informational
FQXDE3302I Autocode synchronization drive image invalidated Informational
FQXDE3303I Autocode synchronization drive image write failure Informational
FQXDE3304I Autocode synchronization drive image invalidate failure Informational
FQXDE3305I Drive image write retry exhausted Informational
FQXDE3306I Insufficient storage for autocode synchronization image Informational
FQXDE3402I Raw data retrieve canceled by user Informational
FQXDE3403I Raw data retrieve canceled by controller Informational
FQXDE3404I Raw data restore start Informational
FQXDE3405I Raw data restore completed Informational
FQXDE3406I Raw data restore canceled by user Informational
FQXDE3407I Raw data restore canceled by controller Informational
FQXDE3408I Raw data retrieve structure inconsistency detected Informational
FQXDE3500I A schedule was created Informational
FQXDE3501I A previously defined schedule was modified Informational
FQXDE3502I A previously defined schedule was deleted Informational
FQXDE3503I A previously defined schedule was enabled Informational
FQXDE3504I A previously defined schedule was disabled Informational
FQXDE3505I The start of a scheduled operation was missed Informational
FQXDE3506I An operation associated with a schedule completed Informational
FQXDE3508I The scheduled time for an operation was reached and the associated action initiated Informational
FQXDE3600I SSD cache created on the storage array Informational
FQXDE3601I SSD cache deleted on the storage array Informational
FQXDE3602I SSD cache suspended Informational
FQXDE3603I SSD cache resumed Informational
FQXDE3607I SSD cache enabled on a volume Informational
FQXDE3608I SSD cache disabled on a volume Informational
FQXDE3609I Drives added to an SSD cache Informational
FQXDE360AI Drives removed from an SSD cache Informational
FQXDE360BI SSD cache performance modeling started Informational
FQXDE360CI SSD cache performance modeling stopped Informational
FQXDE360DI SSD cache performance modeling results reset Informational
FQXDE360EI SSD cache transitioned to optimal Informational
FQXDE360FI SSD cache performance modeling internal structures created on the storage array Informational
FQXDE3610I SSD cache performance modeling internal structures deleted on the storage array Informational
FQXDE3611I SSD cache performed modeling enabled on a volume Informational
FQXDE3612I SSD cache performed modeling disabled on a volume Informational
FQXDE3613I SSD cache renamed Informational
FQXDE3700I Core dump was captured Informational
FQXDE3701I Core dump was not captured Informational
FQXDE3702I Core dump capture failed Informational
FQXDE3703I Core dump retrieval started Informational
FQXDE3704I Core dump retrieval completed Informational
FQXDE3705I Core dump retrieval was cancelled Informational
FQXDE3706I Core dump retrieval has timed out Informational
FQXDE3707I Core dump has not been retrieved and overwritten Informational
FQXDE3708I Core dump restore completed Informational
FQXDE3807I Disk pool drive reconstruction started Informational
FQXDE3808I Disk pool drive reconstruction completed Informational
FQXDE380AI Disk pool reconfiguration started Informational
FQXDE380BI Disk pool reconfiguration completed Informational
FQXDE380EI A disk pool capacity reduction operation started Informational
FQXDE380FI A reconstruction of a critically degraded disk pool volume started Informational
FQXDE3810I A reconstruction of a critically degraded disk pool volume completed Informational
FQXDE4004I Alternate controller quiescence message received Informational
FQXDE4005I Controller quiescence started Informational
FQXDE4006I Alternate controller quiescence started Informational
FQXDE4007I Subsystem quiescence started Informational
FQXDE4008I Controller quiescence halted Informational
FQXDE4009I Controller quiescence released Informational
FQXDE400AI Alternate controller quiescence released Informational
FQXDE400BI All channel reset detected Informational
FQXDE400CI Controller placed offline Informational
FQXDE400DI Controller placed online Informational
FQXDE400EI Automatic volume transfer started Informational
FQXDE400FI Controller reset by its alternate Informational
FQXDE4010I Controller reset Informational
FQXDE4012I Volume not on preferred path due to AVT/RDAC failover Informational
FQXDE5000I Assign component ownership Informational
FQXDE5001I Assign hot spare drive Informational
FQXDE5002I Create volume Informational
FQXDE5003I De-assign hot spare drive Informational
FQXDE5004I Delete volume Informational
FQXDE5006I Fail drive Informational
FQXDE5007I Initialize volume group, disk pool, or volume Informational
FQXDE5008I Initialize drive Informational
FQXDE5009I Controller firmware download started Informational
FQXDE500BI Controller NVSRAM download started Informational
FQXDE500EI Reconstruct drive/volume Informational
FQXDE500FI Start component defragment Informational
FQXDE5010I Add free capacity to component Informational
FQXDE5011I Change RAID level of component Informational
FQXDE5012I Change segment size of volume Informational
FQXDE5014I Change controller to active mode Informational
FQXDE5015I Update cache parameters of storage array Informational
FQXDE5016I Change name of storage array Informational
FQXDE5017I Synchronize controller clock Informational
FQXDE5018I Change cache parameters of volume Informational
FQXDE501AI Change name of volume Informational
FQXDE501BI Place controller online Informational
FQXDE501CI Revive drive Informational
FQXDE501DI Revive volume Informational
FQXDE501EI Change positions of trays in PHYsical view Informational
FQXDE501FI Change media scan (scrub) settings of volume Informational
FQXDE5020I Change media scan (scrub) settings of storage array Informational
FQXDE5021I Reset configuration of storage array Informational
FQXDE5023I Controller return status/function call for requested operation Informational
FQXDE5024I Internal download checkpoint Informational
FQXDE5025I Controller firmware download failed Informational
FQXDE5026I Controller firmware download completed Informational
FQXDE5027I Controller NVSRAM download failed Informational
FQXDE5028I Controller NVSRAM download completed Informational
FQXDE5029I Reset controller battery parameters Informational
FQXDE502AI Assign volume ownership Informational
FQXDE502BI Increase volume capacity Informational
FQXDE5030I Activate mirroring Informational
FQXDE5031I Deactivate mirroring Informational
FQXDE5032I Change synchronization priority Informational
FQXDE5033I Start mirror synchronization Informational
FQXDE5037I Incorrect password attempted Informational
FQXDE5039I Change parameters of volume copy pair Informational
FQXDE503AI Start volume copy operation Informational
FQXDE503BI Stop volume copy operation Informational
FQXDE503CI Change mirrored pair write mode Informational
FQXDE503DI Suspend mirror relationship Informational
FQXDE503EI Resume mirror relationship Informational
FQXDE503FI Resynchronization set for automatic Informational
FQXDE5041I Recover volume Informational
FQXDE5042I Mirror relationships for write consistency group suspended Informational
FQXDE5043I Mirror relationships for write consistency group resumed Informational
FQXDE5044I Configuration change from single to dual or dual to single controller mode Informational
FQXDE5045I Activate controller firmware started Informational
FQXDE5046I Activate controller firmware completed Informational
FQXDE5047I Activate controller firmware failed Informational
FQXDE5048I Clear controller firmware started Informational
FQXDE5049I Clear controller firmware complete Informational
FQXDE504AI Suspend mirror list completed Informational
FQXDE504BI Resume mirror list completed Informational
FQXDE504CI Enable alarm Informational
FQXDE504DI Disable alarm Informational
FQXDE504EI Power down storage array Informational
FQXDE504FI This command is no longer valid Informational
FQXDE5050I Clear controller firmware failed Informational
FQXDE5051I Feature pack key file successfully applied Informational
FQXDE5052I Feature pack key file successfully removed Informational
FQXDE5053I Drive was replaced Informational
FQXDE5054I Create volumes with free capacity (extents) Informational
FQXDE5055I Get volume free capacities (extents) Informational
FQXDE5056I Create component Informational
FQXDE5057I Delete component Informational
FQXDE5058I Set component user label Informational
FQXDE5059I Force component Informational
FQXDE505AI Export component Informational
FQXDE505BI Import component Informational
FQXDE505CI Tray ID changed Informational
FQXDE505DI Importing the component was canceled Informational
FQXDE505EI Importing the component failed Informational
FQXDE505FI Exporting the component failed Informational
FQXDE5060I Volume properties set Informational
FQXDE5061I Drive has become native to this array Informational
FQXDE5062I Drives have become native to this array Informational
FQXDE5063I Reset storage array configuration Informational
FQXDE5064I Volume configuration was reset Informational
FQXDE5065I Security (FDE) storage array key created Informational
FQXDE5066I Security (FDE) storage array key updated Informational
FQXDE5067I Security (FDE) storage array key exported Informational
FQXDE5068I Security (FDE) storage array key set Informational
FQXDE5069I Security (FDE) storage array key set complete Informational
FQXDE506AI External key management enabled Informational
FQXDE506BI External key management disabled Informational
FQXDE506CI New external key installed Informational
FQXDE506EI Created security (FDE) storage array key cleared Informational
FQXDE506FI The installed security (FDE) key is not valid Informational
FQXDE5070I Autosupport enabled Informational
FQXDE5071I Autosupport disabled Informational
FQXDE5072I Enable OnDemand Informational
FQXDE5073I Disable OnDemand Informational
FQXDE5074I OnDemand Remote Diagnostics Enabled Informational
FQXDE5075I OnDemand Remote Diagnostics Disabled Informational
FQXDE5076I External SYMbolAPI access was disabled Informational
FQXDE5077I External SYMbolAPI access was enabled Informational
FQXDE5078I Indication of when the SYMbol command resetSAConfiguration is executed with the type CLEAR_ALL_FACTORY_RESET Informational
FQXDE5079I Indication of when the SYMbol command resetSAConfiguration is executed with the type CLEAR_ALL_SUPPORT_RESET Informational
FQXDE507AI AutoSupport maintenance mode enabled Informational
FQXDE507BI AutoSupport maintenance mode disabled Informational
FQXDE507CI One of the images contained in the controller firmware package failed to authenticate using the provided public key and signature Informational
FQXDE507DI The Controller NVSRAM package failed to authenticate using the provided public key and signature Informational
FQXDE5107I A SAS PHY was enabled Informational
FQXDE5200I Create host group Informational
FQXDE5201I Delete host group Informational
FQXDE5202I Rename host group Informational
FQXDE5203I Create host Informational
FQXDE5204I Delete host Informational
FQXDE5205I Rename host Informational
FQXDE5206I Move host Informational
FQXDE5207I Create host port Informational
FQXDE5208I Delete host port Informational
FQXDE5209I Rename host port Informational
FQXDE520AI Move host port Informational
FQXDE520BI Set host port type Informational
FQXDE520FI Create volume-to-LUN mapping Informational
FQXDE5210I Delete volume-to-LUN mapping Informational
FQXDE5211I Change volume-to-LUN mapping Informational
FQXDE5214I Topology and mappings deleted Informational
FQXDE5216I iSCSI initiator was created Informational
FQXDE5217I iSCSI initiator was deleted Informational
FQXDE5218I Host properties have been set Informational
FQXDE5219I Initiator properties have been set Informational
FQXDE521AI The initiator authentication type was changed Informational
FQXDE521BI The initiator's CHAP secret was changed Informational
FQXDE521CI The target authentication type was changed Informational
FQXDE521DI The target's CHAP secret was changed Informational
FQXDE521EI The target's iSCSI properties were set Informational
FQXDE521FI The target's iSCSI alias was set Informational
FQXDE5220I Create new host port Informational
FQXDE5221I Set host port properties Informational
FQXDE5226I Failed host port registration Informational
FQXDE5227I Inactive host port activated Informational
FQXDE5228I Failed initiator registration Informational
FQXDE5229I Inactive initiator activated Informational
FQXDE522AI Host port records deleted Informational
FQXDE522BI A remote target was created Informational
FQXDE522CI A remote target was deleted Informational
FQXDE522DI The properties for a remote target were set Informational
FQXDE522EI The authentication for a remote target was changed Informational
FQXDE522FI The secret for a remote target was changed Informational
FQXDE5230I The alias for the local initiator was set Informational
FQXDE5231I The properties for the local initiator were set Informational
FQXDE5232I The authentication was set for the local initiator Informational
FQXDE5233I The change secret for the local initiator was set Informational
FQXDE5400I Premium feature enabled Informational
FQXDE5401I Premium feature disabled Informational
FQXDE5404I Feature Enable Identifier changed Informational
FQXDE5407I Evaluation license is about to expire Informational
FQXDE5408I Feature evaluation period was enabled Informational
FQXDE5600I Controller passed diagnostics Informational
FQXDE5601I This controller's alternate passed diagnostics Informational
FQXDE5603I Diagnostics rejected - already in progress Informational
FQXDE5604I Diagnostics rejected this controller's alternate is absent or failed Informational
FQXDE5605I Diagnostics rejected error occurred when sending the Icon message Informational
FQXDE5606I Diagnostics rejected - task unable to queue DIAG_INIT_MSG message Informational
FQXDE5607I Diagnostics returned unknown ReturnCode Informational
FQXDE5608I Diagnostics rejected - test ID is incorrect Informational
FQXDE560AI Diagnostics rejected access volume (UTM) is not enabled Informational
FQXDE5611I Controller passed diagnostics, but loopback test identified an error on loops Informational
FQXDE5612I This controller's alternate passed diagnostics, put loopback test identified an error on loops Informational
FQXDE5613I Diagnostics loopback test identified bad destination channels Informational
FQXDE561AI Diagnostics rejected - data transfer on controller is not disabled (quiesced) Informational
FQXDE561BI Diagnostics rejected data transfer on this controllers alternate is not disabled (quiesced) Informational
FQXDE561CI Diagnostics rejected both controllers must be in active mode Informational
FQXDE561DI Diagnostics initiated from this controller Informational
FQXDE561EI Running diagnostics on this controller Informational
FQXDE561FI Diagnostics rejected download is in progress Informational
FQXDE5620I Cable diagnostic started Informational
FQXDE5621I Cable diagnostic completed Informational
FQXDE5622I An exception condition was detected on the controller Informational
FQXDE5801I Management port link down Informational
FQXDE5802I Management port link up Informational
FQXDE5900I WWN migrated from database is invalid Informational
FQXDE6000I Internal configuration database created Informational
FQXDE6003I Internal configuration database not enough optimal drives available Informational
FQXDE6004I Internal configuration database is being resynchronized Informational
FQXDE6005I Internal configuration database read or write operation failed Informational
FQXDE6006I Internal configuration database merge failed Informational
FQXDE6007I Configuration database successfully adopted Informational
FQXDE6008I Stable storage drive unusable Informational
FQXDE6009I Stable storage drive usable Informational
FQXDE600AI A SSTOR miscompare was detected Informational
FQXDE6100I Internal configuration database cleared Informational
FQXDE6102I Internal configuration database size increased Informational
FQXDE6103I This controller's alternate was reset Informational
FQXDE6104I This controller's alternate failed Informational
FQXDE6105I Internal configuration database file system corrupted Informational
FQXDE6106I Internal configuration database incorrect file system version Informational
FQXDE6108I Configuration information stored in the array's database may have been lost Informational
FQXDE610AI The storage array is no longer in database recovery mode Informational
FQXDE610CI A subrecord validation has taken place, and been fixed Informational
FQXDE610DI Internal configuration database subrecord CRC mismatch Informational
FQXDE6300I Mirror repository volume created Informational
FQXDE6301I Mirror repository volume deleted Informational
FQXDE6403I Data on mirrored pair synchronizing Informational
FQXDE6404I Data on mirrored pair synchronized Informational
FQXDE6405I Associated volume in mirrored pair not present Informational
FQXDE6406I Mirrored pair created Informational
FQXDE6407I Mirrored pair deleted Informational
FQXDE6408I Mirrored pair role changed Informational
FQXDE6409I Mirror relationship suspended Informational
FQXDE640AI Data on mirrored pair unsynchronized Informational
FQXDE640BI Attempt to suspend mirrored pair failed Informational
FQXDE640CI Mirror write mode set to synchronous Informational
FQXDE640DI Mirror write mode set to asynchronous Informational
FQXDE640EI Mirror write mode set to asynchronous, write-consistent Informational
FQXDE640FI Mirror relationship degraded Informational
FQXDE6410I An asynchronous mode for legacy RVM Mirrors is not supported; therefore all legacy RVM mirrors have been deleted Informational
FQXDE6500I Remote volume created Informational
FQXDE6501I Remote volume deleted Informational
FQXDE6502I Communication to remote volume up Informational
FQXDE6504I Remote storage array's world-wide name changed Informational
FQXDE6601I Volume copy pair established Informational
FQXDE6602I Volume copy pair removed Informational
FQXDE6603I Volume copy operation in progress Informational
FQXDE6604I Volume copy operation pending Informational
FQXDE6605I Volume copy operation stopped Informational
FQXDE6606I Volume copy operation completed Informational
FQXDE6701I Unreadable sector repaired Informational
FQXDE6702I All unreadable sectors on the volume repaired data unrecovered Informational
FQXDE6704I Unreadable sectors found on volume Informational
FQXDE6705I Volume import failed - too many unreadable sectors Informational
FQXDE6706I Unreadable sectors prevented data from being reconstructed to a replaced drive. An unreadable sector record was created on the replaced drive to track the fact that the data cannot be read Informational
FQXDE6802I Serial port recovery exited Informational
FQXDE6901I Diagnostic data retrieval operation started Informational
FQXDE6902I Diagnostic data retrieval operation completed Informational
FQXDE6903I Diagnostic data Needs Attention status was cleared Informational
FQXDE6904I Diagnostic data capture information was lost Informational
FQXDE6905I Non-critical data restore failed Informational
FQXDE6906I Diagnostic data capture information available Informational
FQXDE7000I Incorrect feature pack key file Informational
FQXDE7002I Feature bundle key was deleted Informational
FQXDE7003I Invalid feature bundle key was applied Informational
FQXDE7100I Discrete time series activated Informational
FQXDE7101I Discrete time series deactivated Informational
FQXDE7102I Discrete time series expired Informational
FQXDE7103I Histogram activated Informational
FQXDE7104I Histogram deactivated Informational
FQXDE7105I Histogram expired Informational
FQXDE7302I Low battery capacity Informational
FQXDE7303I Battery temperature nominal Informational
FQXDE7304I Battery learn cycle will occur in one hour Informational
FQXDE730BI Battery fully charged Informational
FQXDE730DI Battery replaced Informational
FQXDE730EI Battery capacity is sufficient Informational
FQXDE730FI Incomplete battery learn cycle Informational
FQXDE7310I Learn cycle for battery started Informational
FQXDE7311I Learn cycle for battery completed Informational
FQXDE7504I Cache backup device was replaced Informational
FQXDE7505I Backup metadata database corrupted Informational
FQXDE7600I Cache backup operation started Informational
FQXDE7601I Cache backup operation completed Informational
FQXDE7602I Cache restore from persistent device was started Informational
FQXDE7603I Cache restore operation from persistent device completed Informational
FQXDE7700I Repository volume is created Informational
FQXDE7701I The capacity of a repository was increased Informational
FQXDE7702I The capacity of a repository was decreased Informational
FQXDE7808I Snapshot group was created Informational
FQXDE7809I Snapshot group was deleted Informational
FQXDE780AI The parameters for a snapshot group were set (changed) Informational
FQXDE780BI A snapshot image was created for a volume Informational
FQXDE780CI A snapshot image was deleted Informational
FQXDE780DI A consistency group snapshot image was created Informational
FQXDE780EI A consistency group snapshot image was deleted Informational
FQXDE780FI A snapshot volume was created Informational
FQXDE7810I A snapshot volume was deleted Informational
FQXDE7811I A snapshot volume was disabled (stopped) Informational
FQXDE7812I The parameters for a snapshot volume have been changed Informational
FQXDE7813I Create consistency group Informational
FQXDE7814I Delete consistency group Informational
FQXDE7815I Add member to consistency group Informational
FQXDE7816I Remove member from consistency group Informational
FQXDE7817I The parameters of a consistency group were changed Informational
FQXDE7818I Snapshot image rollback started Informational
FQXDE7819I Consistency group snapshot image rollback started Informational
FQXDE781AI Snapshot image rollback resumed Informational
FQXDE781BI Snapshot image rollback canceled Informational
FQXDE781CI Convert snapshot volume to read-write Informational
FQXDE781DI Consistency group snapshot volume created Informational
FQXDE781EI Consistency group snapshot volume deleted Informational
FQXDE781FI Consistency group snapshot volume disabled (stopped) Informational
FQXDE7820I Parameters on consistency group snapshot volume changed Informational
FQXDE7821I Snapshot volume recreated (re-started) Informational
FQXDE7822I Consistency group snapshot volume recreated (re-started) Informational
FQXDE7823I A scheduled creation of a snapshot image occurred Informational
FQXDE7824I A scheduled creation of a consistency group snapshot image occurred Informational
FQXDE7829I The creation of a consistency group snapshot image is pending Informational
FQXDE782AI A creation of a snapshot image is pending Informational
FQXDE782BI The pending creation of a snapshot image was canceled Informational
FQXDE782CI The pending creation of a consistency group snapshot image was canceled Informational
FQXDE782DI A snapshot group was revived from the failed state Informational
FQXDE782EI A snapshot volume was revived from the failed state Informational
FQXDE782FI A snapshot image rollback was completed Informational
FQXDE7830I Snapshot image rollback activated Informational
FQXDE7B03I A thin volume was created Informational
FQXDE7B04I The virtual capacity of a thin volume was increased Informational
FQXDE7B05I A thin volume was initialized Informational
FQXDE7B06I The capacity threshold of a thin volume repository was changed Informational
FQXDE7B07I The expansion policy of a thin volume was changed Informational
FQXDE7B08I The maximum expansion capacity of a thin volume repository was changed Informational
FQXDE7B09I A Defrag operation started on a Thin Provisioned Repository Volume Informational
FQXDE7B0AI A Defrag operation on a Thin Provisioned Repository Volume completed Informational
FQXDE7B0BI Thin Provisioned Repository Volume capacity was reduced. The freed capacity was returned to the disk pool Informational
FQXDE7B0CI Thin Volume reporting policy changed to report as thin volume Informational
FQXDE7B0DI Thin Volume reporting policy changed to report as thick (fully provisioned) volume Informational
FQXDE7C0CI Asynchronous mirror group was created Informational
FQXDE7C0DI Asynchronous mirror group creation failed Informational
FQXDE7C0EI An asynchronous mirror group was deleted Informational
FQXDE7C0FI The deletion of an asynchronous mirror group failed Informational
FQXDE7C10I The parameters of an asynchronous mirror group was changed Informational
FQXDE7C11I The degraded status of an asynchronous mirror group was cleared Informational
FQXDE7C12I The synchronization interval threshold exceeded condition of an asynchronous mirror group was cleared Informational
FQXDE7C13I Asynchronous mirror group role changed to primary Informational
FQXDE7C14I Asynchronous mirror group role changed to secondary Informational
FQXDE7C15I Asynchronous mirror group role conflict resolved Informational
FQXDE7C16I The manual synchronization of an asynchronous mirror group was initiated Informational
FQXDE7C1BI An asynchronous mirror group was suspended by the user Informational
FQXDE7C1CI An asynchronous mirror group was resumed Informational
FQXDE7C1DI An orphaned asynchronous mirror group was resolved Informational
FQXDE7C1EI A primary member was added to an asynchronous mirror group Informational
FQXDE7C1FI A secondary member placeholder was added to an asynchronous mirror group Informational
FQXDE7C20I A secondary member was added to an asynchronous mirror group Informational
FQXDE7C21I A member of an asynchronous mirror group was removed Informational
FQXDE7C22I A member of an asynchronous mirror group was recovered Informational
FQXDE7C23I Security on an asynchronous mirror group member was enabled Informational
FQXDE7C24I The member repository threshold exceeded condition of an asynchronous mirror group was cleared Informational
FQXDE7C25I The primary member repository full condition of an asynchronous mirror group was cleared Informational
FQXDE7C26I The secondary member repository full condition of an asynchronous mirror group was resolved Informational
FQXDE7C27I Ownership change occurred on member repository of asynchronous mirror group Informational
FQXDE7C28I An orphaned asynchronous mirror group member was resolved Informational
FQXDE7C29I Read error occurred on primary asynchronous group member Informational
FQXDE7C2AI Establishing the synchronization data on all primary members of an asynchronous mirror group failed Informational
FQXDE7C2BI Read error occurred on secondary asynchronous group member Informational
FQXDE7C2CI Read error occurred on mirror delta log Informational
FQXDE7C2DI Fibre channel port activated for asynchronous mirroring Informational
FQXDE7C2EI Fibre channel port deactivated for asynchronous mirroring Informational
FQXDE7C31I A controlled asynchronous mirror group role change request was canceled Informational
FQXDE7C33I An orphaned asynchronous mirror group incomplete member condition was resolved Informational
FQXDE7C35I A mirror has stopped Informational
FQXDE7C36I A role changed member was requested for an asynchronous mirror group Informational
FQXDE7E00I Drive power toggled off Informational
FQXDE7E01I Drive power toggled on Informational
FQXDE7E02I Drive power cycle sequence started Informational
FQXDE7E03I Drive power cycle sequence successfully completed Informational
FQXDE7E04I Drive power cycle sequence aborted Informational
FQXDE7E05I Drive recovery criteria not met Informational
FQXDE7E06I Received a request to power cycle a drive Informational
FQXDE7F00I SNMP Community was added Informational
FQXDE7F01I SNMP Community was removed Informational
FQXDE7F02I SNMP Community parameters was changed Informational
FQXDE7F03I SNMP trap destination was added Informational
FQXDE7F04I SNMP trap destination was removed Informational
FQXDE7F05I SNMP trap destination parameters were changed Informational
FQXDE7F06I SNMP system variable was changed Informational
FQXDE7F07I SNMP test alert Informational
FQXDE9000I The active trace buffer size exceeds the defined threshold Informational
FQXDE9001I IOC Data Captured Informational
FQXDE9100I Auto Load Balancing enabled Informational
FQXDE9101I Auto Load Balancing disabled Informational
FQXDE9104I Analysis of workload balance was performed Informational
FQXDE9105I Workload was automatically balanced by transferring volumes Informational
FQXDE9106I The workload balance was evaluated following load optimization Informational
FQXDE9107I Host Connectivity Reporting disabled Informational
FQXDE9108I Host Connectivity Reporting enabled Informational
FQXDE9202I Security Audit Log Full Policy was changed Informational
FQXDE9203I Security Audit Log entries were manually cleared Informational
FQXDE9205I Directory Services Server configuration was changed Informational
FQXDE9206I The given IP address has attempted too many invalid logins and was locked out for a period of time Informational
FQXDE9209I SAML Server configuration was changed Informational
FQXDE920AI SAML Server is enabled Informational
FQXDE920BI SAML Server is disabled Informational
FQXDE920CI SAML Server authentication was rejected Informational
FQXDE9400I NVMe controller destroyed due to keep alive timeout Informational
FQXDE9401I NVM Connection failed due to lack of available resources Informational
FQXDE9645I Unrecoverable Interrupted Write Informational
FQXDE9715I Storage Array Component - Loss of Communication Informational
FQXDE9740I Degraded Volume Informational
FQXST0004I The specified disk had a bad block, which was corrected. Informational
FQXST0006I Disk group creation failed immediately. Informational
FQXST0009I The specified spare disk has been used in the specified disk group to bring it back to a fault-tolerant status. Informational
FQXST0016I The specified disk has been designated as a global spare. Informational
FQXST0018I Disk group reconstruction completed. Informational
FQXST0019I A rescan has completed. Informational
FQXST0020I Storage Controller firmware has been updated. Informational
FQXST0021I Disk group verification succeeded, failed immediately, or was halted by a user. Informational
FQXST0023I Disk group creation started. Informational
FQXST0025I Disk group statistics were reset. Informational
FQXST0028I Controller parameters were changed. Informational
FQXST0031I The specified disk is no longer a global or dedicated spare. Informational
FQXST0032I Disk group verification started. Informational
FQXST0033I Controller time and date were changed. Informational
FQXST0034I The controller configuration has been restored to factory defaults. Informational
FQXST0037I Disk group reconstruction started. When complete, event 18 is logged. Informational
FQXST0041I The specified disk was designated a spare for the specified disk group. Informational
FQXST0043I The specified disk group was deleted. Informational
FQXST0047I An error detected by the sensors has been cleared. This event indicates that a problem reported by event 39 or 40 is resolved. Informational
FQXST0048I The specified disk group was renamed. Informational
FQXST0049I A lengthy SCSI maintenance command has completed. (This typically occurs during a disk firmware update.) Informational
FQXST0052I Disk group expansion started. Informational
FQXST0053I Disk group expansion completed, failed immediately, or was halted by a user. Informational
FQXST0056I A controller powered up or restarted. Informational
FQXST0058I A disk drive reported an event. Informational
FQXST0059I The controller detected a non-parity error while communicating with the specified SCSI device. The error was detected by the controller, not the disk. Informational
FQXST0068I The controller that logged this event is shut down, or both controllers are shut down. Informational
FQXST0071I The controller started or completed failing over. Informational
FQXST0072I After failover, recovery has started or completed. Informational
FQXST0073I The two controllers are communicating with each other and cache redundancy is enabled. Informational
FQXST0074I The FC loop ID for the specified disk group was changed to be consistent with the IDs of other disk groups. Informational
FQXST0075I The specified volume's LUN (logical unit number) has been unassigned because it conflicts with LUNs assigned to other volumes. This can happen when disks containing data for a mapped volume are moved from one storage system to another. Informational
FQXST0076I The controller is using default configuration settings. This event occurs on the first power up, and might occur after a firmware update. Informational
FQXST0077I The cache was initialized as a result of power up or failover. Informational
FQXST0079I A trust operation completed for the specified disk group. Informational
FQXST0080I The controller enabled or disabled the specified parameters for one or more disks. Informational
FQXST0081I The current controller has restarted the partner controller. The other controller will restart. Informational
FQXST0083I The partner controller is shutting down or restarting. Informational
FQXST0086I Host-port or disk-channel parameters were changed. Informational
FQXST0090I The partner controller does not have a mirrored configuration image for the current controller, so the current controller's local flash configuration is being used. Informational
FQXST0096I Pending configuration changes that take effect at startup were ignored because customer data might be present in cache. Informational
FQXST0103I The name was changed for the specified volume. Informational
FQXST0104I The size was changed for the specified volume. Informational
FQXST0105I The default LUN (logical unit number) was changed for the specified volume. Informational
FQXST0106I The specified volume was added to the specified pool. Informational
FQXST0108I The specified volume was deleted from the specified pool. Informational
FQXST0109I The statistics for the specified volume were reset. Informational
FQXST0110I Ownership of the specified disk group was transferred to the other controller. Informational
FQXST0111I The link for the specified host port is up. Informational
FQXST0112I The link for the specified host port went down because the controller is starting up. Informational
FQXST0114I The link for the specified disk-channel port is down. Note that events 114 and 211 are logged whenever a user-requested rescan occurs and do not indicate an error. Informational
FQXST0118I Cache parameters have been changed for the specified volume. Informational
FQXST0139I The Management Controller (MC) powered up or restarted. Informational
FQXST0140I The Management Controller is about to restart. Informational
FQXST0141I This event is logged when the IP address used for management of the system has been changed by a user or by a DHCP server (if DHCP is enabled). This event is also logged during power up or failover recovery, even when the address has not changed. Informational
FQXST0152I The Management Controller (MC) has not communicated with the Storage Controller (SC) for 160 seconds. Informational
FQXST0153I The Management Controller (MC) re-established communication with the Storage Controller (SC). Informational
FQXST0154I New firmware was loaded in the Management Controller (MC). Informational
FQXST0155I New loader firmware was loaded in the Management Controller (MC). Informational
FQXST0156I The Management Controller (MC) was restarted from the Storage Controller (SC) in a normal case, such as when initiated by a user. Informational
FQXST0170I The last rescan detected that the specified enclosure was added to the system. Informational
FQXST0171I The last rescan detected that the specified enclosure was removed from the system. Informational
FQXST0173I The specified disk group was removed from quarantine. Informational
FQXST0174I An enclosure or disk firmware update has succeeded, been aborted by a user, or failed. If the firmware update fails, the user will be notified about the problem immediately and should take care of the problem at that time, so even when there is a failure, this event is logged as with a severity of Informational. Informational
FQXST0175I The network-port Ethernet link for the specified controller is up or down. Informational
FQXST0176I The error statistics for the specified disk have been reset. Informational
FQXST0177I Cache data was purged for the specified missing volume. Informational
FQXST0181I One or more configuration parameters associated with the Management Controller (MC) were changed, such as the configuration for SNMP, SMI-S, email notification, and system strings (system name, system location, etc.). Informational
FQXST0182I All disk channels have been paused. I/O will not be performed on the disks until all channels are unpaused. Informational
FQXST0183I All disk channels have been unpaused, meaning that I/O can resume. An unpause initiates a rescan, which when complete is logged as event 19. This event indicates that the pause reported by event 182 has ended. Informational
FQXST0185I An enclosure management processor (EMP) write command completed. Informational
FQXST0186I Enclosure parameters were changed by a user. Informational
FQXST0187I The write-back cache is enabled. Event 188 is the corresponding event that is logged when write-back cash is disabled. Informational
FQXST0188I Write-back cache is disabled. Event 187 is the corresponding even that is logged when write-back cache is disabled. Informational
FQXST0189I A disk channel that was previously degraded or failed is now healthy. Informational
FQXST0190I The controller module's supercapacitor pack has started charging. Informational
FQXST0191I The auto-write-through trigger event that caused event 190 to be logged has been resolved. Informational
FQXST0192I The controller module's temperature has exceeded the normal operating range. Informational
FQXST0193I The auto-write-through trigger event that caused event 192 to be logged has been resolved. Informational
FQXST0194I The Storage Controller in the partner controller module is not up. Informational
FQXST0195I The auto-write-through trigger event that caused event 194 to be logged has been resolved. Informational
FQXST0198I A power supply failed. Informational
FQXST0199I The auto-write-through trigger event that caused event 198 to be logged has been resolved. Informational
FQXST0200I A fan failed. Informational
FQXST0201I The auto-write-through trigger event that caused event 200 to be logged has been resolved. Informational
FQXST0202I An auto-write-through trigger condition has been cleared, causing write-back cache to be re-enabled. The environmental change is also logged at approximately the same time as this event (event 191, 193, 195, 199, 201, and 241.) Informational
FQXST0204I The system came up normally, and the NV device is in a normal expected state. Informational
FQXST0205I The specified volume has been mapped or unmapped. Informational
FQXST0206I Disk group scrub started. Informational
FQXST0207I Disk group scrub completed or was stopped by a user. Informational
FQXST0208I A scrub-disk job started for the specified disk. The result will be logged with event 209. Informational
FQXST0209I A scrub-disk job logged with event 208 has completed and found no errors, a disk being scrubbed (with no errors found) has been added to a disk group, or a user has stopped the job. Informational
FQXST0211I SAS topology has changed. The number of SAS expanders has increased or decreased. Informational
FQXST0216I An uncommitted snapshot has been deleted. Removal of the specified snapshot completed successfully. Informational
FQXST0219I Utility priority was changed by a user. Informational
FQXST0235I An enclosure management processor (EMP) reported an event. Informational
FQXST0236I A special shutdown operation started. These special shutdown operations are used as part of the firmware-update process. Informational
FQXST0237I A firmware update started and is in progress. This event provides details of the steps in a firmware-update operation. Informational
FQXST0241I The auto-write-through trigger event that caused event 242 to be logged has been resolved. Informational
FQXST0243I A new controller enclosure has been detected. This happens when a controller module is moved from one enclosure to another and the controller detects that the midplane WWN is different from the WWN it has in its local flash. Informational
FQXST0245I An existing disk channel target device is not responding to SCSI discovery commands. Informational
FQXST0248I A valid feature license was successfully installed. See event 249 for details about each licensed feature. Informational
FQXST0249I After a valid license is installed, this event is logged for each licensed feature to show the new license value for that feature. The event specifies whether the feature is licensed, whether the license is temporary, and whether the temporary license is expired. Informational
FQXST0251I A volume-copy operation started for the specified source volume. Informational
FQXST0253I A license was uninstalled. Informational
FQXST0255I The PBCs across controllers do not match because the PBC from controller A and the PBC from controller B are from different vendors. This might limit the available configurations. Informational
FQXST0259I In-band CAPI commands were disabled. Informational
FQXST0260I In-band CAPI commands were enabled. Informational
FQXST0261I In-band SES commands were disabled. Informational
FQXST0262I In-band SES commands were enabled. Informational
FQXST0266I A volume-copy operation for the specified master volume was stopped by a user. Informational
FQXST0268I A volume-copy operation for the specified volume completed. Informational
FQXST0269I A partner firmware update operation started. This operation is used to copy firmware from one controller to the other to bring both controllers up to the same version of firmware. Informational
FQXST0271I The storage system could not get a valid serial number from the controller's FRU ID SEEPROM, either because it could not read the FRU ID data, because the data in it are not valid or because the data have not been programmed. Informational
FQXST0273I PHY fault isolation was enabled or disabled by a user for the specified enclosure and controller module. Informational
FQXST0275I The specified PHY was enabled. Informational
FQXST0299I The controller's RTC setting was recovered successfully. Informational
FQXST0300I CPU frequency was changed to high. Informational
FQXST0301I CPU frequency was changed to low. Informational
FQXST0302I DDR memory clock frequency was changed to high. Informational
FQXST0303I DDR memory clock frequency was changed to low. Informational
FQXST0304I The controller has detected I2C errors that might have been recovered. Informational
FQXST0305I A serial number in Storage Controller (SC) flash memory was not valid when compared to the serial number in the controller-module or midplane FRU ID SEEPROM. The valid serial number was recovered automatically. Informational
FQXST0306I The controller-module serial number in Storage Controller (SC) flash memory was not valid when compared to the serial number in the controller-module FRU ID SEEPROM. The valid serial number was recovered automatically. Informational
FQXST0309I When the Management Controller (MC) is started, the IP data is obtained from the midplane FRU ID SEEPROM where it is persisted. If the system is unable to write it to the SEEPROM the last time it changed, a flag is set in flash memory. This flag is checked during startup, and if set, this event is logged and the IP data that is in flash memory is used. The IP data might not be correct if the controller module was swapped because the data in the controller's flash memory are used. Informational
FQXST0310I After a rescan, back-end discovery and initialization of data for at least one EMP (Enclosure Management Processor) completed. This event is not logged again when processing completes for other EMPs in the system. Informational
FQXST0311I A user initiated a ping of a host through the iSCSI interface. Informational
FQXST0312I This event is used by email messages and SNMP traps when testing notification settings. This event is not recorded in the event log. Informational
FQXST0316I The temporary license for a feature will expire in 10 days. Any components created with the feature will remain accessible but new components cannot be created after the license expires. Informational
FQXST0352I Expander Controller (EC) assert data or stack-dump data are available. Informational
FQXST0353I Expander Controller (EC) assert data and stack-dump data were cleared. Informational
FQXST0354I The SAS topology has changed on a host port. At least one PHY is active. For example, the SAS cable connecting a controller host port to a host was connected. Informational
FQXST0359I All PHYs that were down for the specified disk channel have recovered and are now up. Informational
FQXST0360I The speed of the specified disk PHY was renegotiated. Informational
FQXST0361I A scheduled task was initiated. Informational
FQXST0362I The scheduler experienced a problem with the specified task. Informational
FQXST0363I When the Management Controller (MC) is restarted, firmware versions that are currently installed are compared against those in the bundle that was most recently installed. If the versions match, this event is logged as Infomational severity. Components checked include the CPLD, Expander Controller (EC), Storage Controller (SC), and MC. Informational
FQXST0364I The broadcast bus is running as generation 1. Informational
FQXST0400I The specified log has filled to a level at which it needs to be transferred to a log-collection system. Informational
FQXST0454I A user changed the drive-spin-down delay for the specified disk group to the specified value. Informational
FQXST0457I The specified virtual pool was created. Informational
FQXST0458I Disk groups were added to the specified virtual pool. Informational
FQXST0459I Removal of the specified disk group(s) was started. When this operation is complete, event 470 is logged. Informational
FQXST0461I The specified disk group that was missing from the specified virtual pool was recovered. This event indicates that a problem reported by event 460 is resolved. Informational
FQXST0462I The specified virtual pool exceeded one of its thresholds for allocated pages. Informational
FQXST0463I The specified virtual pool has dropped below one of its thresholds for allocated pages. This event indicates that a condition reported by event 462 is no longer applicable. Informational
FQXST0465I A user removed an unsupported cable or SFP from the specified controller host port. Informational
FQXST0466I The specified virtual pool was deleted. Informational
FQXST0467I The specified disk group was added successfully. Informational
FQXST0468I The FPGA temperature returned to the normal operating range and the speed of buses connecting the FPGA to downstream adapters was restored. The speed was reduced to compensate for an FPGA over-temperature condition. This event indicates that a problem reported by event 469 is resolved. Informational
FQXST0470I The removal of the specified disk group(s) completed successfully. Informational
FQXST0473I The specified volume is using more than its threshold percentage of its virtual pool. Informational
FQXST0474I The specified volume is no longer using more than its threshold percentage of its virtual pool. This event indicates that the condition reported by event 473 is no longer applicable. Informational
FQXST0477I The CPU temperature exceeded the normal range so the CPU speed was reduced. IOPS were reduced. The storage system is operational, but I/O performance is reduced. Informational
FQXST0478I A problem reported by event 476 or 477 is resolved. Informational
FQXST0487I Historical performance statistics were reset. Informational
FQXST0488I The creation of a volume group started. Informational
FQXST0489I The creation of a volume group completed. Informational
FQXST0490I The creation of a volume group failed. Informational
FQXST0491I The creation of a volume group started. Informational
FQXST0492I The volumes in a volume group were ungrouped. Informational
FQXST0493I A group of volumes was modified. Informational
FQXST0502I The specified SSD has 20% or less of its life remaining. Informational
FQXST0503I The Intelligent BackEnd Error Monitor (IBEEM) has discovered that continuous errors are being reported for the specified PHY. IBEEM logged this event after monitoring the PHY for 30 minutes. Informational
FQXST0504I Service debug access to the system was enabled or disabled by a user. Allowing service debug access might have security implications. After the diagnosis is complete you should disallow such access. Informational
FQXST0506I The addition of the specified disk group started. When this operation is complete, event 467 is logged. Informational
FQXST0507I The link speed of the specified disk does not match the link speed capacity of the enclosure. Informational
FQXST0510I The FDE lock key has been set or changed by a user. Informational
FQXST0511I The FDE import lock key has been set by a user. Informational
FQXST0512I The system was set to the FDE secured state by a user. Informational
FQXST0513I The system was set to the FDE repurposed state by a user. Informational
FQXST0514I The FDE lock key and import key were cleared by a user. Informational
FQXST0515I An FDE disk was repurposed by a user. Informational
FQXST0517I A disk that was formerly in the FDE unavailable state is no longer unavailable. The disk was returned to normal operations. Informational
FQXST0523I This event provides additional details associated with a scrub-disk-group job, expanding on the information in event 206, 207, or 522. Informational
FQXST0533I This event provides details about the result of the MC test of the specified component. Informational
FQXST0551I A SES alert for a power supply in the specified enclosure has been resolved. Informational
FQXST0552I A SES alert for a fan in the specified enclosure has been resolved. Informational
FQXST0553I A SES alert for a temperature sensor in the specified enclosure has been resolved. Informational
FQXST0554I A SES alert for a voltage sensor in the specified enclosure was resolved. Informational
FQXST0555I A SES alert for an expander in the specified enclosure has been resolved. Informational
FQXST0556I A SES alert for an expander in the specified enclosure has been resolved. Informational
FQXST0557I An Enclosure Management Processor (EMP) reported an alert condition on a current sensor. Informational
FQXST0562I Virtual pool statistics were reset. Informational
FQXST0563I A disk was restarted. Informational
FQXST0566I One of the DDR ports has been busy for at least 5 minutes. Informational
FQXST0568I A disk group has mixed physical sector size disks (for example 512n and 512e disks in the same disk group). Informational
FQXST0569I A previously detected SAS host port cable mismatch has been resolved for the specified port number. The proper cable type has been connected. Informational
FQXST0571I Snapshot space exceeded either the low or medium snapshot space threshold. Informational
FQXST0572I The specified virtual pool dropped below one of its snapshot space thresholds. Informational
FQXST0574I A peer connection was created. Informational
FQXST0575I A peer connection was deleted. Informational
FQXST0576I A replication set was created. Informational
FQXST0577I A replication set was deleted. Informational
FQXST0578I A replication started. Informational
FQXST0579I A replication completed. Informational
FQXST0580I A replication was stopped. Informational
FQXST0581I A replication was suspended. Informational
FQXST0584I A peer connection was modified. Informational
FQXST0585I A replication set was modified. Informational
FQXST0586I A replication resumed. Informational
FQXST0594I The specified disk in the specified disk group is missing and the disk group is quarantined. Informational
FQXST0595I The specified disk in the specified disk group is missing and the disk group is quarantined. Informational
FQXDE204EF Recoverable drive hardware failure detected by drive Warning
FQXDE204FF Recoverable drive hardware failure detected by drive Warning
FQXDE2277G Repository volume security incompatibility detected Warning
FQXDE2308F Chassis serial number might be incorrect Warning
FQXDE2866F An IOM (ESM) has reported an exception event Warning
FQXDE3307F Insufficient storage or drive count for autocode synchronization image Warning
FQXDE507EF AutoSupport maintenance mode configuration request failed Warning
FQXDE5108F Controller failover due to lost expansion tray access Warning
FQXDE7801G Snapshot group repository over threshold Warning
FQXDE7804G Snapshot volume repository over threshold Warning
FQXDE7825F A scheduled creation of a snapshot image failed Warning
FQXDE7826F A scheduled creation of a consistency group snapshot image failed Warning
FQXDE7827G A pending creation of a consistency group snapshot image failed Warning
FQXDE7828G A pending creation of a snapshot image failed Warning
FQXDE7900F Copy on write integrity fault Warning
FQXDE7A00F A high level volume utility write ahead log integrity fault Warning
FQXDE7B00G A thin volume repository capacity threshold was exceeded Warning
FQXDE7C00G An asynchronous mirror group was marked degraded Warning
FQXDE7C01G An asynchronous mirror group synchronization interval threshold was exceeded Warning
FQXDE7C05G An asynchronous mirror group is orphaned (no corresponding mirror group on the other storage array) Warning
FQXDE7C07G Asynchronous mirror group member repository threshold was exceeded Warning
FQXDE7C08G An asynchronous mirror group primary member repository is full Warning
FQXDE7C0BG An asynchronous mirror group member is orphaned Warning
FQXDE7C32G The controller firmware detected that only a placeholder volume of an asynchronous mirror group member exists Warning
FQXDE9201G Security Audit Log is nearing maximum capacity and should be cleared now to avoid losing events Warning
FQXDE9300G An installed certificate used for KMIP server authentication is nearing expiration Warning
FQXDE9306G An attempt to create a security key failed as the storage array's client certificate does not match any of the existing owners on the KMIP server Warning
FQXDE9631F Volumes Degraded in Volume Group or Pool - Noncritical Drive Error Warning
FQXDE9777G Repository - Threshold Exceeded Warning
FQXDE9780G Snapshot Volume Repository - Threshold Exceeded Warning
FQXDE9784G Consistency Group Snapshot Image Creation Failed Warning
FQXDE9785G Snapshot Image Creation Failed Warning
FQXDE9786G Thin Volume Repository - Threshold Exceeded Warning
FQXDE9789G Degraded Mirror Group Warning
FQXDE9790G Mirror Group Synchronization - Threshold Exceeded Warning
FQXDE9794G Orphaned Mirror Group Warning
FQXDE9796G Mirrored Volume Repository - Threshold Exceeded Warning
FQXDE9797G Mirrored Primary Volume Repository - Full Warning
FQXDE9799G Orphaned Mirrored Volume Warning
FQXDE9800G Orphaned Mirrored Volume Warning
FQXDE9807G Audit Log - Early Threshold Exceeded Warning
FQXDE9809G Key Management Certificate Nearing Expiration Warning
FQXDE9815G Drive Security Key Creation Failed Warning
FQXDE9816G A controller was placed in Service mode Warning
FQXST0001W The disk group is online but cannot tolerate another disk failure. Warning
FQXST0006W A failure occurred during the initialization of the specified disk group. Warning
FQXST0008W A disk group is down, a disk group failed, or a disk group reported that it has no life remaining. Warning
FQXST0021W Disk group verification did not complete due to an internally detected condition, such as a failed disk. If a disk fails, data might be at risk. Warning
FQXST0039W The sensors monitored a temperature or voltage in the warning range. When the problem is resolved, event 47 is logged for the component that logged event 39. Warning
FQXST0044W The controller contains cache data for the specified volume but the corresponding disk group is not online. Warning
FQXST0050W A correctable ECC error occurred in cache memory. Warning
FQXST0051W An uncorrectable ECC error occurred in cache memory. Warning
FQXST0053W Too many errors occurred during disk group expansion to allow the expansion to continue. Warning
FQXST0055W The specified disk reported a SMART event. Warning
FQXST0058W A disk drive reset itself due to an internal logic error. Warning
FQXST0059W The controller detected a parity event while communicating with the specified SCSI device. The event was detected by the controller, not the disk. Warning
FQXST0062W The specified global or dedicated spare disk failed. Warning
FQXST0078W The controller could not use an assigned spare for a disk group because the spare's capacity is too small. Warning
FQXST0084W The current controller that logged this event forced the partner controller to fail over. Warning
FQXST0087W The mirrored configuration retrieved by this controller from the partner controller has a bad cyclic redundancy check (CRC). The local flash configuration will be used instead. Warning
FQXST0088W The mirrored configuration retrieved by this controller from the partner controller is corrupt. The local flash configuration will be used instead. Warning
FQXST0089W The mirrored configuration retrieved by this controller from the partner controller has a configuration level that is too high for the firmware in this controller to process. The local flash configuration will be used instead. Warning
FQXST0112W The link for the specified host port went down unexpectedly. Warning
FQXST0117W This controller module detected or generated an error on the specified host channel. Warning
FQXST0127W The controller detected a disk dual-port connection that is not valid. This event indicates that a controller host port is connected to an expansion port, instead of to a port on a host or a switch. Warning
FQXST0136W Errors detected on the specified disk channel have caused the controller to mark the channel as degraded. Warning
FQXST0152W The Management Controller (MC) has not communicated with the Storage Controller (SC) for 15 minutes and might have failed. Warning
FQXST0156W The Management Controller (MC) was restarted from the Storage Controller (SC) for the purpose of error recovery. Warning
FQXST0158W A correctable ECC error occurred in Storage Controller CPU memory. Warning
FQXST0162W The host WWNs (node and port) previously presented by this controller module are unknown. Warning
FQXST0163W The host WWNs (node and port) previously presented by the partner controller module, which is currently offline, are unknown. Warning
FQXST0166W The RAID metadata level of the two controllers does not match, which indicates that the controllers have different firmware levels. Warning
FQXST0167W A diagnostic test at controller boot detected an abnormal operation, which might require a power cycle to correct. Warning
FQXST0172W The specified disk group was quarantined because some its disks are not accessible. Warning
FQXST0203W An environmental change occurred that allows write-back cache to be enabled, but the auto-write-back preference is not set. The environmental change is also logged at approximately the same time as this event (event 191, 193, 195, 199, 201, or 241). Warning
FQXST0204W While starting, the system found an issue with the NV device. The system will attempt to recover itself. Warning
FQXST0207W Disk group scrub did not complete because of an internally detected condition, such as a failed disk. Warning
FQXST0209W A scrub-disk job logged with event 208 has been stopped by a user, or has reassigned a disk block. These bad-block replacements are reported as "other errors". If this disk is used in a non-fault-tolerant disk group, data might have been lost. Warning
FQXST0211W SAS topology has changed. No elements are detected in the SAS map. Warning
FQXST0218W The supercapacitor pack is near the end of life. Warning
FQXST0232W The maximum number of enclosures allowed for the current configuration has been exceeded. Warning
FQXST0233W The specified disk type is not valid and is not allowed in the current configuration. Warning
FQXST0238W A licenses feature cannot be installed because the license is not valid. Warning
FQXST0239W A timeout occurred while flushing the CompactFlash. Warning
FQXST0240W A failure occurred while flushing the CompactFlash. Warning
FQXST0246W The coin battery is not present, is not properly seated, or has reached end-of-life. Warning
FQXST0247W The FRU ID SEEPROM for the specified field replaceable unit (FRU) cannot be read. FRU ID data might not be programmed. Warning
FQXST0250W A license could not be installed. Warning
FQXST0263W The specified spare disk is missing. Either it was removed, or it is not responding. Warning
FQXST0270W A problem occurred while reading or writing the persistent IP data from the FRU ID SEEPROM, or the data read from the FRU ID SEEPROM were not valid. Warning
FQXST0274W The specified PHY was disabled, either automatically or by a user. Warning
FQXST0298W The controller's real-time clock (RTC) setting is not valid. Warning
FQXST0316W The temporary license for a feature has expired. Warning
FQXST0319W The specified available disk failed. Warning
FQXST0322W The controller has an older Storage Controller (SC) version than the version used to create the CHAP authentication database in the flash memory of the controller. Warning
FQXST0354W The SAS topology has changed on a host port. At least one PHY went down. For example, the SAS cable connecting a controller host port to a host was disconnected. Warning
FQXST0355W The debug button on the controller module was found to be stuck in the On position during boot. Warning
FQXST0356W This event can only result from tests that are run in the manufacturing environment. Warning
FQXST0357W This event can only result from tests that are run in the manufacturing environment. Warning
FQXST0358W Some PHYs are down for the specified disk channel. Warning
FQXST0361W The scheduler experienced a problem with the specified schedule. Warning
FQXST0362W The scheduler experienced a problem with the specified task. Warning
FQXST0365W An uncorrectable ECC error occurred in Storage Controller CPU memory. Warning
FQXST0401W The specified log has filled to a level at which diagnostic data will be lost if the log is not transferred to a log-collection system. Warning
FQXST0412W One disk in the specified RAID-6 disk group failed. The disk group is online, but it has a status of FTDN (fault tolerant with a down disk). Warning
FQXST0442W Power-On Self Test (POST) diagnostics detected a hardware error in a UART chip. Warning
FQXST0455W The controller detected that the configured host-port link speed exceeded the capability of an FC SFP. The speed has been automatically reduced to the maximum value supported by all hardware components in the data path. Warning
FQXST0456W The IQN of the system was generated from the default OUI because the controllers could not read the OUI from the midplane FRU ID data during startup. If the IQN is not correct for the system, iSCSI hosts might be unable to access the system. Warning
FQXST0462W The specified virtual pool exceeded its high threshold for allocated pages, and the virtual pool is overcommitted. Warning
FQXST0464W A user inserted an unsupported cable or SFP into the specified controller host port. Warning
FQXST0469W The speed of buses connecting the FPGA to downstream adapters was reduced to compensate for an FPGA over-temperature condition. The storage system is operational but I/O performance is reduced. Warning
FQXST0476W The CPU temperature exceeded the safe range so the CPU entered its self-protection state. IOPS were reduced. The storage system is operational, but I/O performance is reduced. Warning
FQXST0482W One of the PCIe buses is running with fewer lanes than is optimal. Warning
FQXST0484W No compatible spares are available to reconstruct this disk group if it experiences a disk failure. Only disk groups that have dedicated or suitable global spares will start reconstruction automatically. Warning
FQXST0485W The specified disk group was quarantined to prevent writing outdated data that might exist in the controller that logged this event. Warning
FQXST0486W A recovery process was initiated to prevent writing outdated data that might exist in the controller that logged this event. Warning
FQXST0495W The algorithm for best-path routing selected the alternate path to the specified disk because the I/O error count on the primary path reached its threshold. Warning
FQXST0496W An unsupported disk type was found. Warning
FQXST0502W The specified SSD has 5% or less of its life remaining. Warning
FQXST0505W The specified virtual pool was created with a size smaller than 500 GB, which can lead to unpredictable behavior. The storage system might not perform correctly. Warning
FQXST0522W A scrub-disk-group job encountered an error at the specified logical block address. Warning
FQXST0531W The specified controller module detected a stall. The system will perform corrective actions. Warning
FQXST0545W A controller module is connected to a legacy enclosure midplane, resulting in degraded performance. Warning
FQXST0548W Disk group reconstruction failed. Warning
FQXST0551W An EMP reported that a power supply unit (PSU) was uninstalled. Warning
FQXST0552W An EMP reported one of the following: Warning
FQXST0553W A temperature sensor is not within normal operating temperature thresholds but is within safe operating limits; or, a temperature sensor has been uninstalled. Warning
FQXST0554W A voltage sensor is not within the normal operating range but is within safe operating limits; or, a voltage sensor was removed. Warning
FQXST0555W An expander in a controller module, expansion module, or drawer is mated but is not responding; or, an expander in an expansion module has been removed. Warning
FQXST0556W An expander in a controller module, expansion module, or drawer is mated but is not responding; or, an expander in an expansion module has been removed. Warning
FQXST0557W An Enclosure Management Processor (EMP) reported an alert condition on a current sensor. Warning
FQXST0565W One of the PCIe buses is running at less than optimal speed. Warning
FQXST0569W A SAS host cable mismatch was detected for the specified port number. The specified alternate PHYs have been disabled. Warning
FQXST0571W Snapshot space exceeded the high snapshot space threshold. Warning
FQXST0573W Snapshot space for a virtual pool cannot be reduced because no snapshots can be deleted. Warning
FQXDE1010M Impending drive failure detected by drive Error
FQXDE101EM Impending drive failure detected by controller Error
FQXDE1020M Data assurance drive was locked out Error
FQXDE1207M Fibre channel link errors - threshold exceeded Error
FQXDE1208M Data rate negotiation failed Error
FQXDE1209M Drive channel set to Degraded Error
FQXDE120AM SFP failed Error
FQXDE120DM Host-side SFP failed Error
FQXDE1403M Excessive reboots (exceptions) have occurred on the controller Error
FQXDE150EM Controller loop-back diagnostics failed Error
FQXDE150FM Channel miswire Error
FQXDE1510M IOM (ESM) miswire Error
FQXDE1513M Individual drive - Degraded path Error
FQXDE1515M Drive Channel hardware failed Error
FQXDE151AM Optical link speed detection failure Error
FQXDE151EM Controller miswire for drive channel occurred Error
FQXDE1522M Drive enclosure type miswire Error
FQXDE1524M Trunk incompatible IOM (ESM) Error
FQXDE1525M Fibre trunk miswire Error
FQXDE1650M SAS host channel miswire detected Error
FQXDE1652L SAS source driver partner initiator overflow Error
FQXDE1654L Host wide port is degraded Error
FQXDE165AM An error was detected during SAS backend discovery processing Error
FQXDE1700M Invalid SAS topology detected Error
FQXDE1702M SAS host adapter miswire detected Error
FQXDE1704M SAS IOM (ESM) miswire detected Error
FQXDE1706M Optimal wide port becomes degraded Error
FQXDE1707M Degraded wide port becomes failed Error
FQXDE170AM Drive expansion port miswire Error
FQXDE170FM Controller wide port has gone to degraded state Error
FQXDE1710M Controller wide port has gone to failed state Error
FQXDE171AM A controller may have lost access to expansion trays Error
FQXDE180AM Failed I/O host card; iSCSI interface error detected Error
FQXDE1904M Failed host interface card Error
FQXDE1907M Controller was locked down due to too many missing drives Error
FQXDE1908M A controller detected that the combination of host interface cards are out of compliance with limitations of the controller or the firmware. Error
FQXDE200AM Data/parity mismatch on volume Error
FQXDE202EM Read drive error during interrupted write Error
FQXDE203BM Drive failed due to un-recoverable read error during scan Error
FQXDE2045M Redundancy group not consistent during reconfiguration Error
FQXDE2046L Isolation of drive causing redundancy mismatch Error
FQXDE2047L Different Data Returned On Read Retry Error
FQXDE2048L Data altered to correct redundancy mismatch Error
FQXDE2069M Controller is in Service Mode due to excessive Data Assurance errors Error
FQXDE206AM Controller is in Analysis Lockdown Mode due to excessive Data Assurance errors Error
FQXDE2109M Controller cache not enabled - cache sizes do not match Error
FQXDE210CM Controller cache battery failed Error
FQXDE210EM Controller cache memory recovery failed after power cycle or reset Error
FQXDE2110L Controller cache memory initialization failed Error
FQXDE2113M Controller cache battery nearing expiration Error
FQXDE211BM Batteries present but NVSRAM file configured for no batteries Error
FQXDE211EM Current cache size is unsupported Error
FQXDE211FM Insufficient cache backup device capacity Error
FQXDE2120M Insufficient processor memory for cache Error
FQXDE2124M Dedicated mirror channel failed Error
FQXDE2125L Integrity check failed during cache restore Error
FQXDE2126L Backup of cache to persistent device did not complete Error
FQXDE212BM Write-back caching forcibly disabled Error
FQXDE212EM Cached data may have been lost Error
FQXDE2131M Dirty cache not flushed on the only active controller Error
FQXDE222DM Drive manually failed Error
FQXDE2249M Physical drive replacement is too small Error
FQXDE224AM Drive has wrong block size Error
FQXDE224BM Drive failed - initialization failure Error
FQXDE224DM Drive failed - no response at start of day Error
FQXDE224EM Drive failed - initialization/reconstruction failure Error
FQXDE2250M Volume failure Error
FQXDE2251M Drive failed - reconstruction failure Error
FQXDE2252M Drive marked offline during interrupted write Error
FQXDE2260M Uncertified Drive Detected Error
FQXDE2262M Failed drive replaced with wrong drive type Error
FQXDE2266M Volume modification operation failed Error
FQXDE2267M Incompatible drive due to invalid configuration on drive Error
FQXDE226BM Security (FDE) key needed Error
FQXDE226CM Drive failure Error
FQXDE226DM Assigned drive or hot spare-in use drive removed Error
FQXDE226EM Solid state drive at end of life Error
FQXDE2271M Physical drive has unsupported capacity Error
FQXDE2273M Hot spare in use Error
FQXDE2274M Component is missing Error
FQXDE2275M Component incomplete Error
FQXDE2276M Interposer FW version unsupported Error
FQXDE2278M Incompatible alignment for emulation drive Error
FQXDE227CM Waiting for eligible copy destination to start drive copy Error
FQXDE2285M Impending drive failure detected by drive Error
FQXDE2287M A NTP domain server name is either invalid or the configured primary or secondary DNS servers are unreachable Error
FQXDE2288M Either the NTP server's resolved or configured IP address is wrong or the IP address is unavailable via the attached network Error
FQXDE2289M The DNS/NTP configuration on this controller is either incorrect or all the NTP servers are unreachable over the network Error
FQXDE2302M SBB validation failure for power supply Error
FQXDE2303M Mismatched midplane EEPROM contents Error
FQXDE2304M Two wire interface bus failure Error
FQXDE2305M VPD EEPROM corruption Error
FQXDE2500M Controller removed Error
FQXDE2602L Automatic controller firmware synchronization failed Error
FQXDE2604M Persistent controller memory parity error Error
FQXDE2607M Inconsistent security (FDE) storage array lock key Error
FQXDE2705M Multiple mismatched key ids found Error
FQXDE2801M Storage array running on UPS battery Error
FQXDE2803M UPS battery - two minutes to failure Error
FQXDE280AM Controller tray component removed Error
FQXDE280BM Controller tray component failed Error
FQXDE280DM Drive tray component failed or removed Error
FQXDE2816M Tray ID conflict - duplicate IDs across drive trays Error
FQXDE281BM Nominal temperature exceeded Error
FQXDE281CM Maximum temperature exceeded Error
FQXDE281DM Temperature sensor removed Error
FQXDE281EM IOM (ESM) firmware mismatch Error
FQXDE2823M Drive by-passed Error
FQXDE2829M Controller redundancy lost Error
FQXDE282BM Drive tray path redundancy lost Error
FQXDE282DM Drive path redundancy lost Error
FQXDE282FM Incompatible version of IOM (ESM) firmware detected Error
FQXDE2830M Mixed drive types out of compliance Error
FQXDE2831M Uncertified IOM (ESM) detected Error
FQXDE2832M Uncertified drive tray detected Error
FQXDE2833M Controller host interface card ID mismatch Error
FQXDE2835M Drive trays not cabled correctly Error
FQXDE2836M Discrete lines diagnostic failure Error
FQXDE2838M Interconnect/battery canister removed Error
FQXDE283BM Power supply failed Error
FQXDE2841M Controller submodel mismatch Error
FQXDE2849M IOM (ESM) Hardware mismatch Error
FQXDE284BL Link Speed (data rate) switch position has changed Error
FQXDE284EM Redundant power-fan canisters required - only one power-fan canister detected Error
FQXDE284FM Misconfigured tray Error
FQXDE2852M IOM (ESM) configuration settings version mismatch Error
FQXDE2854M Drive port bypassed - Error thresholds exceeded Error
FQXDE2855M Controller cannot read alternate controller board ID Error
FQXDE2856M Drawer failed Error
FQXDE2857M Drawer open or removed Error
FQXDE285DM Expansion tray thermal shutdown Error
FQXDE285FM A drawer in the tray has become degraded Error
FQXDE2861M A drawer was detected that is not valid Error
FQXDE2862M A drawer was removed Error
FQXDE2863M Host-side SFP failed Error
FQXDE2864M Host-side SFP unsupported Error
FQXDE2900L Entering invalid system configuration Error
FQXDE3604M SSD cache failed due to cache size mismatch on the two controllers Error
FQXDE3605M SSD cache has associated non-optimal drives Error
FQXDE3803M Disk pool reconstruction reserved drive count is below threshold Error
FQXDE3804M Disk pool utilization exceeded the warning threshold Error
FQXDE3805M Disk pool utilization exceeded the critical threshold Error
FQXDE3809M All of the disk pool's free capacity was used Error
FQXDE380CM Disk pool configuration has insufficient memory Error
FQXDE380DL Disk pool has corrupted database record Error
FQXDE4011M Volume not on preferred path due to AVT/RDAC failover Error
FQXDE5005M Place controller offline Error
FQXDE5038L Storage array 10-minute lockout; maximum incorrect passwords attempted Error
FQXDE5040M Place controller in service mode Error
FQXDE506DM Security (FDE) key failed validation attempts due to excessive tries Error
FQXDE5100M Base controller diagnostic failed Error
FQXDE5101M Base controller diagnostic on alternate controller failed Error
FQXDE5102M IOC fault diagnostic failure was detected Error
FQXDE5103L SAS PHY disabled bypassed port Error
FQXDE5104L SAS PHY disabled bypassed drive Error
FQXDE5105M SAS PHY disabled local wide port Error
FQXDE5106M SAS PHY disabled shared wide port Error
FQXDE5222M Invalid host OS index detected Error
FQXDE5223M Invalid default OS index detected Error
FQXDE5224M Inactive host port registered Error
FQXDE5225M Inactive initiator registered Error
FQXDE5402M Premium feature out of compliance Error
FQXDE5403M Premium feature exceeds limit Error
FQXDE5405M Gold Key - mismatched settings Error
FQXDE5406M Mixed drive types - mismatched settings Error
FQXDE5409M Feature evaluation period expiration is imminent Error
FQXDE560DM Diagnostics read test failed on controller Error
FQXDE560EM This controller's alternate failed diagnostics read test Error
FQXDE560FM Diagnostics write test failed on controller Error
FQXDE5610M This controller's alternate failed diagnostics write test Error
FQXDE5616M Diagnostics rejected configuration error on controller Error
FQXDE5617M Diagnostics rejected - configuration error on this controller's alternate Error
FQXDE6101L Internal configuration database full Error
FQXDE6107M This controller's alternate is non-functional and is being held in reset Error
FQXDE6109M The controller is booting up in database recovery mode Error
FQXDE610BM The subrecord validation failed and could not be fixed Error
FQXDE6400M Dual primary volume conflict Error
FQXDE6401M Dual secondary volume conflict Error
FQXDE6402M Data on mirrored pair unsynchronized Error
FQXDE6411M Mirror relationship has inconsistent write mode Error
FQXDE6503M Communication to remote volume down Error
FQXDE6505M Failed to communicate storage array's world-wide name Error
FQXDE6600M Volume copy operation failed Error
FQXDE6700M Unreadable sectors detected data loss occurred Error
FQXDE6703M Overflow in unreadable sector database Error
FQXDE6800L Serial port recovery activated Error
FQXDE6801L Serial port recovery had an incorrect password Error
FQXDE6900M Diagnostic data is available Error
FQXDE7001M Feature pack key file required Error
FQXDE7300M Battery backup unit overheated Error
FQXDE7301M Insufficient learned battery capacity Error
FQXDE7306M Battery missing Error
FQXDE7308M Battery expired Error
FQXDE7500M Persistent cache backup device failed Error
FQXDE7501M Cache backup device is write-protected Error
FQXDE7506L Backup component status unknown Error
FQXDE7800M Snapshot image rollback paused Error
FQXDE7802M Snapshot group repository full Error
FQXDE7803M Snapshot group failed Error
FQXDE7805M Snapshot volume repository full Error
FQXDE7806M Snapshot volume repository failed Error
FQXDE7807M Snapshot image purged Error
FQXDE7B01M A thin volume repository is full Error
FQXDE7B02M A thin volume repository failed Error
FQXDE7C02M An asynchronous mirror group was suspended internally Error
FQXDE7C03M The asynchronous mirror group has a role (primary or secondary) conflict Error
FQXDE7C04M A recovery point for an asynchronous mirror group was lost Error
FQXDE7C06M Asynchronous mirror group member failed Error
FQXDE7C09M An asynchronous mirror group secondary member repository is full Error
FQXDE7C34M An asynchronous mirror group's synchronization has paused because the alternate state is preventing synchronization from proceeding Error
FQXDE7C37M Controller firmware detected a role change for an AMG was paused Error
FQXDE7D00M SMART Command Transfer (SCT) commands unsupported Error
FQXDE9102M Loss of host-side connection redundancy detected Error
FQXDE9103M Host multipath driver configuration error detected Error
FQXDE9200M Security Audit Log reached its maximum capacity and cannot record new security audit events until it is cleared Error
FQXDE9204M A Directory Services server is unreachable or misconfigured Error
FQXDE9207L The certificate was revoked Error
FQXDE9208L Unable to contact the OCSP responder server Error
FQXDE9301M An installed certificate used for KMIP server authentication has expired Error
FQXDE9302M A certificate error was returned by the KMIP server Error
FQXDE9303M Authentication to the KMIP server failed Error
FQXDE9304M A failure occurred on the connection to a KMIP server Error
FQXDE9305M A general error was returned when communicating with the KMIP server Error
FQXDE9600M Impending Drive Failure (High Data Availability Risk) Error
FQXDE9601M Impending Drive Failure (Medium Data Availability Risk) Error
FQXDE9602M Impending Drive Failure (Unassigned or Standby Hot Spare) Error
FQXDE9603M Incompatible PI-Type Drive Error
FQXDE9604M Degraded Drive Channel Error
FQXDE9605M Controller Reboots Detected Error
FQXDE9606M ESM Canister Miswire Error
FQXDE9607M Degraded Drive Path Error
FQXDE9608M Drive Channel Data Rate Detection Mismatch Error
FQXDE9609M   Error
FQXDE9610M Fibre Channel Trunking - Incompatible ESM Error
FQXDE9611M Fibre Channel Trunking Miswire Error
FQXDE9612M SAS Device Miswire Error
FQXDE9614M SAS Loop Miswire Error
FQXDE9616M SAS Host Miswire Error
FQXDE9618M SAS Device Miswire Error
FQXDE9619M Failed or Degraded SAS Port Error
FQXDE9620M Failed or Degraded SAS Port Error
FQXDE9624M Tray - Loss of External Redundancy Error
FQXDE9625M Failed Host I/O Card Error
FQXDE9626M Host Switch Card Problem Error
FQXDE9627M Missing Drives Lockdown Error
FQXDE9628M A controller detected that the combination of host interface cards are out of compliance with limitations of the controller or the firmware. Error
FQXDE9629M Failed Drive Error
FQXDE9630M Redundancy Group Not Consistent Error
FQXDE9633M Cache Memory Mismatch Error
FQXDE9634M Battery Failed Error
FQXDE9635M Cache Data Loss Error
FQXDE9636M Battery Nearing Expiration Error
FQXDE9637M Battery Settings Mismatch Error
FQXDE9638M Unsupported Cache Memory Size Error
FQXDE9639M Insufficient Cache Backup Device Capacity Error
FQXDE9640M Insufficient processor memory for cache Error
FQXDE9641M Dedicated Mirror Channel Failed Error
FQXDE9642M Write-Back Caching Disabled Error
FQXDE9644M Controller Degraded to Preserve Offline Volume Data Error
FQXDE9646M Incompatible Drive Due to Unsupported Sector Size Error
FQXDE9648M Failed Volume Error
FQXDE9649M Uncertified Drive Error
FQXDE9650M Replaced Drive - Wrong Type Error
FQXDE9651M Volume Modification Operation Failed Error
FQXDE9652M Configuration Database Adoption Failed - RAID Level Not Supported Error
FQXDE9653M Configuration Database Adoption Failed - One or More Limit(s) Exceeded Error
FQXDE9654M Incompatible Drive Due to Older Configuration Database Error
FQXDE9656M Incompatible Drive Due to Newer Configuration Database Error
FQXDE9657M Foreign Drive Has Inconsistent Configuration Error
FQXDE9658M Foreign Drive Refers to Native Drive Error
FQXDE9659M Replaced Drive - Wrong Type Error
FQXDE9660M Failed Legacy Drive Error
FQXDE9661M Configuration Database Adoption Failed - Multiple Configuration Databases Detected Error
FQXDE9662M Native Volume Group And Foreign Drive Refer to Each Other Error
FQXDE9664M Volume Group Clones Error
FQXDE9665M Multiple Volume Groups Refer to Foreign Drive Error
FQXDE9666M Multiple Volume Groups Refer to Foreign Drive (Scenario 2) Error
FQXDE9667M Unsupported SATA Protocol Connection Error
FQXDE9669M Security Key Needed Error
FQXDE9671M Missing Hot Spare Drive Error
FQXDE9672M Solid State Disk - End of Life Error
FQXDE9673M Unsupported Drive Capacity Error
FQXDE9674M Volume - Hot Spare in Use Error
FQXDE9675M Missing Volume Group or Disk Pool Error
FQXDE9676M Incomplete Volume Group or Disk Pool Error
FQXDE9677M Incompatible Interposer Firmware Error
FQXDE9678M Incompatible Drive Alignment Error
FQXDE9679M Impending Drive Failure (Waiting for Hot Spare) Error
FQXDE9682M Unable to Resolve NTP Server's IP Address Error
FQXDE9683M NTP Query Failed Error
FQXDE9684M Unable to Contact NTP Servers Error
FQXDE9685M Invalid Power Supply Error
FQXDE9686M Mismatched Midplane EEPROMs Error
FQXDE9687M Failed I2C Bus Error
FQXDE9688M Corrupt VPD EEPROM Error
FQXDE9689M Controller Removed Error
FQXDE9690M Drive Security Key Mismatch Error
FQXDE9691M Mismatching Security Key IDs Error
FQXDE9692M Lost AC Power Error
FQXDE9693M Removed Power-Fan Canister Error
FQXDE9694M Failed Interconnect-Battery Canister Error
FQXDE9695M Power Supply - No Power Input Error
FQXDE9696M Storage Array Component - Loss of Communication Error
FQXDE9697M Removed ESM Canister Error
FQXDE9699M Tray ID Conflict Error
FQXDE9700M Nominal Temperature Exceeded Error
FQXDE9701M Maximum Temperature Exceeded Error
FQXDE9702M Removed Power-Fan Canister Error
FQXDE9703M ESM Firmware Mismatch Error
FQXDE9704M Bypassed Drive Error
FQXDE9705M Drive Tray - Loss of Path Redundancy Error
FQXDE9706M Bypassed Drive Error
FQXDE9707M Drive - Loss of Path Redundancy Error
FQXDE9708M ESM Hardware Type Mismatch Error
FQXDE9709M Mixed Drive Types - Out of Compliance Error
FQXDE9710M Uncertified ESM Canister Error
FQXDE9711M Uncertified Drive Error
FQXDE9712M Controller Mismatch Error
FQXDE9713M Drive Trays Not Cabled Correctly Error
FQXDE9714M Discrete Lines Diagnostic Failure Error
FQXDE9716M Removed Interconnect-Battery Canister Error
FQXDE9717M Failed Power Supply Error
FQXDE9718M Controller Mismatch Error
FQXDE9720M Redundant Power Supplies Required Error
FQXDE9721M Misconfigured Tray Error
FQXDE9722M ESM Configuration Settings Version Mismatch Error
FQXDE9724M Controller Model or Submodel Identifier Cannot Be Determined Error
FQXDE9725M Failed Drawer Error
FQXDE9726M Missing or Open Drawer Error
FQXDE9727M Thermal Shutdown Error
FQXDE9728M Degraded Drawer Error
FQXDE9729M Invalid Drawer Type Error
FQXDE9730M Drawer Removed Error
FQXDE9731M Failed GBIC/SFP Error
FQXDE9734M Non-Optimal SSD Cache Error
FQXDE9735M Preservation Capacity Below Threshold Error
FQXDE9736M Disk Pool Capacity - Warning Threshold Exceeded Error
FQXDE9737M Disk Pool Capacity - Critical Threshold Exceeded Error
FQXDE9738M Disk Pool Capacity - Full Error
FQXDE9739M Insufficient Disk Pool Memory Error
FQXDE9742M Too Many Security Key Validation Attempts Error
FQXDE9743M Offline Controller Error
FQXDE9744M Controller Diagnostics Failed Error
FQXDE9746M Unknown Component Failure Error
FQXDE9747M Unknown Shared Component Failure Error
FQXDE9748M Invalid Host Type Error
FQXDE9750M Inactive host port registered Error
FQXDE9751M Inactive Host Port Identifier Error
FQXDE9752M External Key Management System - Out of Compliance Error
FQXDE9753M Snapshot Premium Feature - Out Of Compliance Error
FQXDE9754M Gold Key - mismatched settings Error
FQXDE9755M Mixed drive types - mismatched settings Error
FQXDE9756M Premium Feature Trial Nearing Non-Compliant State Error
FQXDE9757M Offline Controller Error
FQXDE9758M Storage Array in Recovery Mode Error
FQXDE9759M Dual Primary Volume Conflict Error
FQXDE9760M Dual Secondary Volume Conflict Error
FQXDE9761M Mirror Data Unsynchronized Error
FQXDE9762M Mirror relationship has inconsistent write mode Error
FQXDE9763M Mirror Communication Error - Unable to Contact Storage Array Error
FQXDE9764M Unable to Update Remote Mirror Error
FQXDE9765M Failed Copy Operation Error
FQXDE9766M Unreadable Sectors Detected Error
FQXDE9767M Unreadable Sectors Log Full Error
FQXDE9768M Controller Diagnostic Data Collected Error
FQXDE9769M Premium Feature - Out of Compliance Error
FQXDE9770M Battery Temperature - Critical Limit Exceeded Error
FQXDE9771M Battery Replacement Required Error
FQXDE9772M Battery Removed Error
FQXDE9773M Battery Expired Error
FQXDE9774M Cache Backup Device Failed Error
FQXDE9775M Cache Backup Device in Write-Protect Mode Error
FQXDE9776M Snapshot Image Rollback Paused Error
FQXDE9778M Repository - Full Error
FQXDE9779M Snapshot Group or CG Member Volume Failed Error
FQXDE9781M Snapshot Volume Repository - Full Error
FQXDE9782M Snapshot Volume Failed Error
FQXDE9783M Snapshot Image Purged Error
FQXDE9787M Thin Volume Repository - Full Error
FQXDE9788M Thin Volume Failed Error
FQXDE9791M Synchronization Suspended Error
FQXDE9792M Mirror Group Role Conflict Error
FQXDE9793M Synchronization Recovery Point Lost Error
FQXDE9795M Failed Mirror Error
FQXDE9798M Mirrored Secondary Volume Repository - Full Error
FQXDE9801M Synchronization Paused Error
FQXDE9802M Mirror Communication Error - Unable to Contact Storage Array Error
FQXDE9803M Incompatible SATA Drive Error
FQXDE9804M Host Redundancy Lost Error
FQXDE9805M Host Multipath Driver Incorrect Error
FQXDE9806M Audit Log Full Error
FQXDE9808M Directory Services Server Connection Failed Error
FQXDE9810M Key Management Certificate Expired Error
FQXDE9811M Key Management Client Certificate Invalid Error
FQXDE9812M Key Management Server Certificate Invalid Error
FQXDE9813M Key Management Server Connection Failed Error
FQXDE9814M Key Management Server Error Error
FQXST0003M The specified disk group went offline. Error
FQXST0007M In a testing environment, a controller diagnostic failed and reported a product-specific diagnostic code. Error
FQXST0021M Disk group verification completed. Errors were found but not corrected. Error
FQXST0040M The sensors monitored a temperature or voltage in the failure range. When the problem is resolved, event 47 is logged for the component that logged event 40. Error
FQXST0050M A correctable ECC error occurred in cache memory more than 10 times during a 24-hour period, indicating a probable hardware fault. Error
FQXST0051M An uncorrectable ECC error occurred in cache memory more than once during a 48-hour period, indicating a probable hardware fault. Error
FQXST0058M A disk drive detected a serious error, such as a parity error or disk hardware failure. Error
FQXST0061M The controller reset a disk channel to recover from a communication error. This event is logged to identify an error trend over time. Error
FQXST0065M An uncorrectable ECC error occurred in cache memory on startup. Error
FQXST0091M In a testing environment, the diagnostic that checks hardware reset signals between controllers in Active-Active mode failed. Error
FQXST0095M Both controllers in an Active-Active configuration have the same serial number. Non-unique serial numbers can cause system problems. For example, WWNs are determined by serial number. Error
FQXST0107M A serious error was detected by the controller. In a single-controller configuration, the controller will restart automatically. In an Active-Active configuration, the partner controller will stop the controller that experienced the error. Error
FQXST0116M After a recovery, the partner controller was stopped while mirroring write-back cache data to the controller that logged this event. The controller that logged this event was restarted to avoid losing the data in the partner controller's cache, but if the other controller does not restart successfully, the data will be lost. Error
FQXST0157M A failure occurred when trying to write to the Storage Controller (SC) flash chip. Error
FQXST0158M A correctable ECC error occurred in Storage Controller CPU memory more than once during a 12-hour period, indicating a probable hardware fault. Error
FQXST0161C One or more enclosures do not have a valid path to an enclosure management processor (EMP). All enclosure EMPs are disabled. Error
FQXST0204M An error occurred with either the NV device itself or the transport mechanism. The system may attempt to recover itself. Error
FQXST0207M Disk group scrub completed and found an excessive number of errors for the specified disk group. Error
FQXST0209M A scrub-disk job logged with event 208 has completed and found one or more media errors, SMART events, or hard (non-media) errors. If this disk is used in a non-fault-tolerant disk group, data might have been lost. Error
FQXST0217M A supercapacitor failure occurred in the controller. Error
FQXST0235M An enclosure management processor (EMP) detected a serious error. Error
FQXST0236M A special shutdown operation started. These special shutdown operations indicate an incompatible feature. Error
FQXST0237M A firmware update attempt was stopped because of general system health issue(s), or because unwritable cache data that would be lost during a firmware update. Error
FQXST0242M The controller module's CompactFlash card has failed. Error
FQXST0267M While cleaning up resources in metadata at the end of a volume-copy operation, the firmware found at least one error for the specified volume. Error
FQXST0269M A partner firmware upgrade attempt stopped because of either general system health issue(s) or unwritable cache data that would be lost during a firmware update. Error
FQXST0307C A temperature sensor on a controller FRU detected an over-temperature condition that caused the controller to shut down. Error
FQXST0313M The specified controller module failed. This event can be ignored for a single-controller configuration. Error
FQXST0314M The specified FRU failed, or is not operating properly. This event follows some other FRU-specific event indicating a problem. Error
FQXST0315C The controller module is not compatible with the enclosure. Error
FQXST0317M A serious error has been detected on the disk interface of the Storage Controller. The controller will be stopped by its partner. Error
FQXST0358C All PHYs are down for the specified disk channel. The system is degraded and is not fault tolerant because all disks are in a single-ported state. Error
FQXST0361C The scheduler experienced a problem with the specified schedule. Error
FQXST0361M The scheduler experienced a problem with the specified schedule. Error
FQXST0362C The scheduler experienced a problem with the specified task. Error
FQXST0362M The scheduler experienced a problem with the specified task. Error
FQXST0363M When the Management Controller (MC) is restarted, firmware versions that are currently installed are compared against those in the bundle that was most recently installed. Error
FQXST0365M An uncorrectable ECC error occurred in Storage Controller CPU memory more than once, indicating a probable hardware fault. Error
FQXST0402M The specified log has wrapped and has started to overwrite the oldest diagnostic data. Error
FQXST0460M The specified disk group is missing from the specified virtual pool. This may be caused by missing disk drives, or unconnected or powered-off enclosures. Error
FQXST0462M The specified virtual pool reached its storage limit. Error
FQXST0479M The controller reporting this event was not able to flush data to or restore data from non-volatile memory. Error
FQXST0480M An IP address conflict was detected for the specified iSCSI port of the storage system. The specified IP address is already in use. Error
FQXST0481M The periodic monitor of CompactFlash hardware detected an error. The controller was put in write-through mode, which reduces I/O performance. Error
FQXST0483M The expansion-module connection for the specified disk channel is not valid. An egress port is connected to an egress port, or an ingress port is connected to an incorrect egress port. Error
FQXST0501M The enclosure hardware is not compatible with the I/O module firmware. The Expander Controller firmware detected an incompatibility with the midplane type. As a preventive measure, disk access was disabled in the enclosure. Error
FQXST0508M The specified virtual pool went offline. All of its volumes also went offline. Error
FQXST0509M The metadata volume for the specified virtual pool went offline. Volume mappings and persistent reservations are inaccessible or lost. Error
FQXST0516M An FDE disk was placed in the unavailable state. Error
FQXST0518M An FDE disk operation failed. Error
FQXST0521M An error occurred while accessing the midplane SEEPROM to store or fetch Full Disk Encryption keys. The midplane's memory is used to store the FDE lock key. Error
FQXST0524M A temperature or voltage sensor reached a critical threshold. Error
FQXST0527M Expander Controller (EC) firmware is incompatible with the enclosure. Error
FQXST0528M Expander Controller firmware detected that the partner Expander Controller (EC) firmware is incompatible with the enclosure. Error
FQXST0529M The local Expander Controller (EC) is incompatible with the enclosure. Error
FQXST0530M The local Expander Controller (EC) firmware detected a level of incompatibility with the partner Expander Controller (EC). This incompatibility could be due to unsupported hardware or firmware. Error
FQXST0531M The specified controller module was unable to recover from a stall. The system will need to be recovered manually. Error
FQXST0533M This event provides details about the result of the MC test of the specified component. Error
FQXST0546M The controller that logged this event stopped the partner controller because it has an incompatible host port configuration. Error
FQXST0549C The specified controller module detected that it recovered from an internal processor fault. Error
FQXST0550C The read data path between the Storage Controller and the disk drives was detected to be unreliable. The Storage Controller took action to correct this. Error
FQXST0551M An error condition was found for a power supply unit (PSU). Error
FQXST0552M An EMP reported an alert condition. A hardware failure has been detected and all fans in the specified FRU have failed. Error
FQXST0553M A temperature sensor is not within the normal operating range, but it is within safe operating limits; or, a temperature sensor has been removed. Error
FQXST0554M A voltage sensor is outside a critical voltage threshold in the specified FRU. Error
FQXST0555M The local Expander Controller firmware has detected a level of incompatibility with the partner Expander Controller firmware or hardware. As a preventive measure, the local Expander Controller might disable all the PHYs. Error
FQXST0557M An Enclosure Management Processor (EMP) reported an alert condition on a current sensor. Error
FQXST0571M Snapshot space exceeded the configured percentage limit of the virtual pool. Error
FQXST0590M A disk group has been quarantined. Error